manualshive.com logo in svg

Porsche 2015 911 GT3 Cup, Technical Manual

Share
Download
Porsche 2015 911 GT3 Cup Technical Manual Download Page 291

 

 

Electrical System 

6.12.3

 

Windscreen wiper 

The wiper motor is activated by the display via the LIN. 

A green push  button is provided on the steering wheel. The wiper motor has two 

stages: slow and fast. 

Switching logic:

 

 

Press once short: 

 

 

one time on 

Press once longer 1,5 second:  continuity wiping 

Press once short: 

 

 

off 

 

 

 

6.12.4

 

Interior fan switch 

The On/Off switch is located in the center console. The fan speed is not adjustable. 

Another switch in the center console controls the  air distribution. There are two 

options: “Screen” (windscreen) and “Driver”. The fan is used to cool the driver or to 

ensure a clear view when the windshield is misting up. 

6.12.3.1

 

6.12.4.1

 

Version: 16.12.2014 

     

 

 

290 

911 GT3 Cup (991) 

MY 2015 

 

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands