Porsche 2015 911 GT3 Cup Technical Manual Download Page 176

Page: 176 / 321

Bodywork

911 GT3 Cup (991)

MY 2015

4.4

Body shell

4.4.1

General

In the development of the body of the new 911 GT3 Cup (991), the following

objectives were pursued, in order to further enhance the safety and performance:

•

Weight reduction combined with improved strength/stiffness

•

Intelligent multi-material selection

•

State-of-the-art joining technologies

•

Aluminum–steel hybrid construction

4.4.1.1

The new 911 GT3 Cup (991) has a completely newly developed body in aluminum-

steel hybrid construction. The idea behind this concept of intelligent lightweight

construction is to use the “right material in the right place”. This means:

•

Large-scale use of aluminum to reduce the vehicle weight

•

Use of ultra-high strength steel to increase body stiffness and to optimize
occupant safety

•

Improved weight distribution

•

Well-adjusted balance

Version: 16.12.2014

175

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands

Porsche 2015 911 GT3 Cup, Technical Manual

Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands