Porsche 2015 911 GT3 Cup Technical Manual Download Page 205

Page: 205 / 321

Bodywork

911 GT3 Cup (991)

MY 2015

Preparation for repairing the front section

These instructions describe how to repair the front section. Individual operations are

shown on one side and have to be carried out inversely on the other side. In case of

deviations, the steps are described separately. The estimated time for the described

repair is approximately five hours.

Remove the following parts:

•

Fender left/right

•

Headlights left/right

•

Wheel arch liners left/right

•

Underbody, front

•

Chassis left/right

•

Front apron

•

Front bumper

•

Fuel tank

•

Brake lines left

•

Draining the coolant, front

•

Water cooler and cooling hoses left/right

•

Steering gear

•

Air jack, front and cross member

•

Master cylinder, remove if required

Version: 16.12.2014

204

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands

Porsche 2015 911 GT3 Cup, Technical Manual

Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands