manualshive.com logo in svg

Porsche 2015 911 GT3 Cup, Technical Manual

Share
Download
Porsche 2015 911 GT3 Cup Technical Manual Download Page 200

 

 

Bodywork 

911 GT3 Cup (991) 

MY 2015 

4.14.1

 

Fuel 

Superplus unleaded (at least 98 ROZ) 

The ethanol content in the fuel may not exceed 26 % (E26). 

4.14.2

 

Defueling 

A defueling valve is installed to empty the fuel tank. To start the procedure, the fuel 

pump switch located in the central console must be in position "Fuel Pump Service". 

The  fuel pump  is  then  activated  for  120 seconds.  If this time is not sufficient to 

completely drain the fuel tank, the switch has to be set again from the center position 
(fuel pump off) to  "Service".  Keep the fuel only in  suitable containers!  The switch 

Intank Pump Service has no function. 

Switching logic of the fuel pump switches (center console):

 

 

Switch position    

up   

Defueling mode 

Switch position    

center 

Off 

Switch position    

down  

Normal mode 

 

 

The fuel  pump  should  not  run dry  as this may  cause 
damage to the pump. 

 

 

 

 

Danger – risk of fire and explosion! 

Fuel may evaporate into the air! 

•

 

No smoking! 

•

 

Identify safety area 

NOTE 

4.14.2.1

 

DANGER 

Version: 16.12.2014 

199 

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands