manualshive.com logo in svg

Porsche 2015 911 GT3 Cup, Technical Manual

Share
Download
Porsche 2015 911 GT3 Cup Technical Manual Download Page 187

 

 

Bodywork 

911 GT3 Cup (991) 

MY 2015 

 

4.8

 

Air jack system 

The air jack system is supplied by Krontec. The vehicle has three lifting jacks, one in 
the middle of the front section and two in the area of the B-pillars, firmly attached to 

the body. The lifting jacks are not adjustable for height and must not be adjusted to a 

ride height change. The compressed air supply valve is installed in the area of the 

passenger’s B-pillar (rear side window). The maximum working pressure is about 35-

38 bar (508-551 psi). 

Important notes 

 

 

Never work below the vehicle lifted with the air  jack 

system without protecting it against  accidental 

lowering. 

 

 

 

 

Never open the air jack. The system is under pressure 

even in the retracted position! 

 

 

 

To prevent damage to the air jack end stops, never let 

the air jacks extend freely (i.e. without vehicle load).  

NOTE 
 

WARNING 

WARNING 

Version: 16.12.2014 

     

 

 

186 

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands