Pitney Bowes relay 2000 Operator'S Manual Download Page 75

Page: 75 / 92

Troubleshooting and Error Messages • 6

6-3

SV63139 Rev. A

Issue

Possible Solutions

INSERTER

Blank Screen

No power.

Check that the power cord is firmly connected and

the wall socket is switched ON.

Inserter not

switched ON.

Turn the power switch (located on left side) ON.

Inserter will not Operate

Cover open.

Check that all covers are closed - check display for

cover information.

Feed trays/fold

plates not located

correctly.

Remove and relocate all feeders and fold plates.

Verify they are in the correct positions and fully

seated.

Insertion Problems

Outer envelope

contents do not

enter the envelope

correctly.

Check the envelope troubleshooting information.
Check that the fold selected is correct for the

material size.
If running heavy or light material, the envelope stop

adjustment might need changing.

General Troubleshooting

Summary of Contents for relay 2000




























































































Search results

Summary of Contents for relay 2000

Reviews:

Related manuals for relay 2000

Brands by name

Popular brands

Pitney Bowes relay 2000, Operator'S Manual

Search results

Summary of Contents for relay 2000

Reviews:

Related manuals for relay 2000

Brands by name

Popular brands