Pitney Bowes relay 2000 Operator'S Manual Download Page 56

Page: 56 / 92

4 • OMR Scanning

4-4

SV63139 Rev. A

OMR Scanning Types

Basic OMR

•  Enables the collation of multi-page documents.
•  Enables you to vary the number of pages per envelope.
•  The inserter folds each OMR sheet separately and inserts it into an

envelope, starting with the last sheet of the set and adding each folded

sheet in turn until the address sheet has been inserted.

Enhanced OMR

• Allows you to stop feeding sheets at selected points in a run and/or

select whether the other feeders are used.

• It provides a higher level of mailpiece integrity so that sensitive

documents are not sent to the wrong customer.

OMR Mark Positions

For the inserter scanners to read the printed OMR marks correctly, they

must

be located within a defined range of positions on the page.

• Standard

OMR positions

•

Offset

OMR positions allow the marks to be positioned further down

the page.

Summary of Contents for relay 2000




























































































Search results

Summary of Contents for relay 2000

Reviews:

Related manuals for relay 2000

Brands by name

Popular brands

Pitney Bowes relay 2000, Operator'S Manual

Search results

Summary of Contents for relay 2000

Reviews:

Related manuals for relay 2000

Brands by name

Popular brands