Piper Aircraft Corporation Malibu Mirage PA-46-350P, Airplane Maintenance Manual

Page: 582 / 1956

PAGE 4
Feb 28/07
3E14
27-50-00
PIPER AIRCRAFT, INC.
PA-46-350P, MALIBU MIRAGE
MAINTENANCE MANUAL
(c) For right flap drive pushrod
1 Remove AN24-34A bolt, two 82695-97 bushings, one NAS1149F0432P washer, two
each NAS1149F0663P and NAS1149F0632P washers, and MS21042-4 nut securing
pushrod clevis to the tube assembly, the aft link assembly, and the arm assembly.
2 Remove NAS 464-P5A9 bolt, and MS 21042-5 nut that secures the pushrod clevis to
the right inboard bellcrank assembly.
(d) Slide pushrod from flap drive housing and remove.
(6) To remove the inboard bellcrank: (See Figure 3.)
(a) Remove the NAS 464-P5A9 bolt and MS21042-5 nut that secures the bellcrank to the flap
drive pushrod.
(b) Remove the AN310-4 nut, AN4-11 bolt, NAS1149F0463P washer, NAS1149F0432P
washers and MS24665-134 pin that secures the inboard bellcrank to the interconnect
pushrod assembly.
(c) Remove the NAS464-P4A8 bolt, MS21042-4 nut, and NAS1149F0463P washer that
secures the bellcrank to the 82913-2 pushrod.
(d) Remove the AN4-45 bolt, AN310-4 nut, 82695-38 bushing, and MS24665-134 pin that
secures the bellcrank to its support bracket.
(e) Remove bellcrank.
(7) To remove the 82913-2 inboard flap actuator pushrod assembly: (See Figure 3.)
(a) Remove the NAS464-P4A8 bolt, MS21042-4 nut, and NAS1149F0463P washer that
secures the pushrod to the bellcrank.
(b) Remove the AN4-12A bolt, MS21042-4 nut, and two NAS1149F0463P washers, that
secures the pushrod to the support bracket on the flap.
(c) Remove the pushrod.
(8) To remove the flap interconnect pushrod assembly: (See Figure 3.)
(a) Remove the AN310-4 nut, AN4-11 bolt, NAS1149F0463P washer, NAS1149F0432P
washers and MS24665-134 pin that secures the interconnect pushrod assembly to the
inboard bellcrank.
(b) Remove the AN310-4 nut, AN4-13 bolt, two NAS1149F0463P washers, MS24665-134 pin
and two 82695-39 bushings that secures the pushrod to the 82977-2 pushrod assembly.
(c) Remove the pushrod.
(9) To remove the idler: (See Figure 3.)
(a) Remove the AN310-4 nut, AN4-13 bolt, two NAS1149F0463P washers, MS24665-134 pin
and two 82695-39 bushings that secures idler arm assembly to the interconnect pushrod
assembly and the 82977-2 pushrod assembly clevis.
(b) Remove the AN310-4 nut, AN4-16 bolt, two NAS1149F0463P washers, MS24665-134 pin
and 82695-40 bushing that secures the pushrod to its support bracket.
(c) Remove the idler arm assembly.
(10) To remove the 82977-2 pushrod assembly: (See Figure 3.)
(a) Remove the AN310-4 nut, AN4-13 bolt, two NAS1149F0463P washers, MS24665-134 pin
and two 82695-39 bushings that secures 82977-2 pushrod assembly clevis to the idler
arm assembly.
(b) Remove the NAS464-P4A8 bolt, MS21042-4 nut, and NAS1149F0432P washer, that
secures the pushrod to the outboard bellcrank assembly.
(c) Remove the 82977-2 pushrod assembly.