Piper Aircraft Corporation Malibu Mirage PA-46-350P Airplane Maintenance Manual Download Page 430

Page: 430 / 1956

PAGE 14
Feb 28/07

2I8

24-30-00

PIPER AIRCRAFT, INC.

PA-46-350P, MALIBU MIRAGE

MAINTENANCE MANUAL

Trouble

Cause

Remedy

CHART 2 (Sheet 2 of 2)

TROUBLESHOOTING (BATTERY SYSTEM)

Electrolyte runs out

Too much water added

Drain and keep at proper

of vent plugs.

to battery.

level. Clean and recharge
battery, vents and acid
recovery jar.

Excessive corrosion

Spillage from over-

Use care in adding water.

inside container.

fillings.

Vent lines leaking or

Replace vent lines. Also,

clogged.

clean and recharge acid
recovery jar.

Battery freezes.

Discharged battery.

Replace battery, clean and
recharge acid recovery jar.

Water added and battery

Always recharge battery

not charged immediately.

at least 1/2 hour when
adding water in freezing
weather.

Leaking cell.

Replace battery. Clean and
recharge acid recovery jar.

Battery polarity reversed.

Connected backwards on

Battery should be slowly

airplane or charger.

discharged completely
and then charged
correctly and tested.

Battery consumes

Cracked jar (one cell only).

Replace battery. Clean and

excessive water.

recharge acid recovery jar.

Battery Disconnect Solenoid

Open circuit.

Repair wiring.

does not operate.

Open-circuited solenoid coil.

Replace unit.

Battery Disconnect Solenoid

Short-circuited coil.

Replace coil.

intermittent operation.

Loose electrical connection.

Clean and tighten electrical
connections.

Badly burned points.

If points cannot be dressed
down, replace the unit.

Summary of Contents for Malibu Mirage PA-46-350P





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands

Piper Aircraft Corporation Malibu Mirage PA-46-350P, Airplane Maintenance Manual

Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands