Piper Aircraft Corporation Malibu Mirage PA-46-350P Airplane Maintenance Manual Download | Manualshive

Page: 407 / 1956

background image

PAGE 1

Feb 28/07

2H9

23-60-00

PIPER AIRCRAFT, INC.

PA-46-350P, MALIBU MIRAGE

MAINTENANCE MANUAL

STATIC DISCHARGING

Static Wicks

(PIR-PPS55006, Rev. U.)

This airplane is equipped with 16 static wicks: three on the outboard end of each aileron, three on the
outboard half of each side of the elevator; two on the right-hand side of the rudder and one on the left-
hand side of the rudder and one in the center of the elevator trim tab.

To aid in dissipating static electricity buildup, the ailerons, elevator and rudder are bonded to either the
control’s hinge or spar.

When replacing the jumper assemblies (bonding straps), secure the end of the jumper that mounts to
the control’s hinge or spar as follows: (see also 51-80-00)

A.

Clean an area of 1 1/2 times the diameter of the jumper’s washer down to bare metal.

B.

Attach the jumper and washer to the control’s hinge or spar.

C.

Seal the cleaned area with a light coat of epoxy primer within 24 hours.

«
...
405
406
407
408
409
...
»

Summary of Contents for Malibu Mirage PA-46-350P





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Malibu Mirage PA-46-350P

Brand: Eaton Pages: 12

Brand: EINHELL Pages: 24

Brand: Ranger Products Pages: 8

Brand: Garland Pages: 16

Brand: Parkside Pages: 18

Brand: Hakko Electronics Pages: 2

GKIT3.6VLIT-2IN1TRHLB

Brand: Gardeo Pages: 29

Brand: OEM Tools Pages: 8

Brand: Greenlee Pages: 16

Brand: Chicago Pneumatic Pages: 36

Brand: Eastwood Pages: 4

Brand: NovoPress Pages: 46

Brand: Gude Pages: 44

Brand: Triton Pages: 12

Brand: Fein Pages: 118

Brand: Facom Pages: 2

Mobile Problast 80017

Brand: Vaniman Pages: 5

Brand: HARTING Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands