Piper Aircraft Corporation Malibu Mirage PA-46-350P Airplane Maintenance Manual Download | Manualshive

Page: 315 / 1956

background image

PAGE 3

Feb 28/07

2D13

21-40-00

PIPER AIRCRAFT, INC.

PA-46-350P, MALIBU MIRAGE

MAINTENANCE MANUAL

3.

Heat Exchanger

NOTE: Remove heat exchanger/air selector valve/plenum assembly before individually removing heat

exchanger.

A.

Removal

(a)

Remove four bolts and hardware attaching bleed air shutoff valve to heat exchanger.

(b)

Remove twelve screws attaching heat exchanger to selector valve.

(c)

Remove twelve screws attaching heat exchanger to plenum.

(d)

Remove heat exchanger from assembly.

B.

Installation

(1)

Align heat exchanger into proper position.

(2)

Attach heat exchanger to plenum with twelve screws.

(3)

Attach heat exchanger to selector valve with twelve screws.

(4)

Attach bleed air shutoff valve to heat exchanger with four bolts and hardware.

4.

Plenum

NOTE: Remove heat exchanger/air selector valve/plenum assembly before individually removing

plenum.

A.

Removal

(1)

Remove twelve screws attaching plenum to heat exchanger.

(2)

Remove plenum.

B.

Installation

(1)

Seal plenum to heat exchanger with RTV 106 sealant.

(2)

Install plenum to heat exchanger with twelve screws.

5.

Defroster

A.

Removal

(1)

Remove closeout panel covering magnetic (float) compass and windshield defroster.by
removing compass deviation and removing screw securing deviation card holder and close out
panel

(2)

Remove the four screws and nylon spacers securing defroster to windshield post.

(3)

Loosen clamps securing defrost hoses to defroster. Remove hoses.

(4)

Remove defroster.

B.

Installation

(1)

Connect defrost hoses to appropriate fittings on defroster. Tighten clamps screws.

(2)

Position defroster at windshield post. Secure with four nylon spacers and screws

(3)

Position closeout panel in appropriate position over defroster and magnetic (float) compass

(4)

Position compass deviation card holder in proper location. Be sure screw hole in deviation card
holder aligns with screw hole in closeout panel. Secure both in position with brass screw
previously removed.

NOTE: Only a brass screw may be used to secure compass card holder and close out panel

to windshield post.

«
...
313
314
315
316
317
...
»

Summary of Contents for Malibu Mirage PA-46-350P





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Malibu Mirage PA-46-350P

Brand: Earlex Pages: 4

Brand: tacwise Pages: 5

Brand: Gechter Pages: 60

BlackFin CT-2980

Brand: Panduit Pages: 12

Brand: QUINN Pages: 4

Brand: TE Connectivity Pages: 8

Brand: Master Appliance Pages: 2

Brand: Fein Pages: 59

Brand: molex Pages: 7

Brand: Yokota Pages: 7

Brand: Pattfield Ergo Tools Pages: 92

Brand: MSW Pages: 21

Brand: Narex Pages: 44

MajorSlice 350A

Brand: Rice Lake Pages: 2

Brand: Triton Pages: 72

Brand: Centroform Pages: 7

Brand: Interchange Pages: 24

BOMAG BVP 10/36

Brand: Fayat Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands