Piper Aircraft Corporation Malibu Mirage PA-46-350P, Airplane Maintenance Manual

Page: 587 / 1956

PAGE 9
Feb 28/07 3E19
27-50-00
PIPER AIRCRAFT, INC.
PA-46-350P, MALIBU MIRAGE
MAINTENANCE MANUAL
(d) Attach flap interconnect pushrod to upper arms on bellcrank. Use NAS1149F0432P
washers as required (Max 4 top, 4 bottom permitted), maintaining neutral alignment of
bearing within the bellcrank. Secure pushrod with AN4-11 bolt (head pointing down), one
NAS1149F0463P washer (under nut), and AN310-4 nut. Install MS24665-134 cotter pin.
(e) Attach inboard flap actuator 82913-2 pushrod to long arms on bellcrank with NAS464-
P4A8 bolt, NAS1149F0463P washer, and MS21042-4 nut.
(f) Attach flap drive pushrod to lower arms on bellcrank with the NAS464-P5A9 bolt and
MS21042-5 nut.
(8) To install the flap drive pushrod assembly: (See Figures 2 and 3.)
(a) Adjust the pushrod(s) being installed to measure as follows (rod end holes - center to
center):
- right pushrod = 27.34 inches
- left pushrod = 18.58 inches.
(b) Slide the pushrod through appropriate flap drive housing.
(c) For left flap drive pushrod:
1 Position flap drive pushrod clevis in center of U bracket on actuator-motor assembly.
Insert the two 82695-96 bushings. Place U shaped clevis of link “E” over actuator-
motor bracket. Secure with AN4-16A bolt, NAS1149F0432P washer (under bolt
head), NAS1149F0463P washer (under nut), and MS21042-4 nut.
2 Secure other end of pushrod to the left inboard bellcrank assembly with a NAS464-
P5A9 bolt, and MS21042-5 nut.
(d) Attach right flap drive pushrod:
1 Position flap drive pushrod in U shaped bracket on end of tube assembly. Insert the
two 82695-97 bushings. Position the U shaped bracket on end of arm assembly over
bushings with one each NAS1149F0663P and NAS1149F0632P washers between
bushings and arm assembly bracket. Secure with the AN24-34A bolt, placing
NAS1149F0432P washer under the nut. Install MS21042-4 nut.
2 Secure other end of pushrod to the right inboard bellcrank assembly with a NAS464-
P5A9 bolt, and MS21042-5 nut.
(e) Tighten the hose clamp on the small end of the bellows.
(9) To install the aft link assembly: (See Figure 2.)
(a) Position aft link on mounting brackets. Secure with AN4H34 bolt, two NAS1149F0463P
washers (under nut), and AN310-4 nut. Tighten nut finger tight plus one or two
castellations. Ensure that the aft link operates freely. Install MS24665-132 cotter pin and
safety with MS20995C32 wire.
(b) Install two 82695-97 bushings in hole in tube assembly. Move aft link arms over hole in
tube assembly. Move arm assembly yoke over hole, placing one each NAS1149F0663P
and NAS1149F0632P washers between yoke and aft link arms. Insert AN24-34A bolt
through yoke, arms, and actuator. Secure bolt with NAS1149F0432P washer and
MS21042-4 nut.
(c) Connect the flap position indicator cable to arm of the aft link assembly using the
PS10036 swing keeper.