Piper Aircraft Corporation Malibu Mirage PA-46-350P Airplane Maintenance Manual Download Page 847

Page: 847 / 1956

PAGE 3

Feb 28/07

4F21

32-60-00

PIPER AIRCRAFT, INC.

PA-46-350P, MALIBU MIRAGE

MAINTENANCE MANUAL

CHART 1 (Sheet 3 of 3)

TROUBLESHOOTING LANDING GEAR WARNING SYSTEMS

Trouble

Cause

Remedy

Green gear down lights

Failed instrument panel

Replace switch.

dim though position

light control switch.

light switch is off.

(Lights grounding

and gear is down and

through dimming

locked.

resistor instead of instrument
panel light control.)

Green gear down light

Gear down limit switch

Replace switch.

fails to go out with

failed.

gear in transit or retracted.

Green gear down lights

Green light ground

Replace resistor.

will go out and not

dimming resistor

dim when position light

open.

switch is turned on though gear
is down and locked.

Green gear down lights

Micro switch out of

Adjust micro switch.

blink momentarily before

adjustment.

the down lock is engaged
on roller.

Summary of Contents for Malibu Mirage PA-46-350P





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands

Piper Aircraft Corporation Malibu Mirage PA-46-350P, Airplane Maintenance Manual

Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands