Paradyne FrameSaver SLV 9664 User Manual Download Page 194

Page: 194 / 240

SNMP MIBs and Traps, and RMON Alarm Defaults

B-8

9664-A2-GB20-00

March 2000

Traps: linkUp and linkDown

These traps are supported on the following interfaces:

Network ISDN S/T interface – Physical sublayer interfaces

Synchronous data port – Physical sublayer interfaces

Frame relay logical link layer interfaces

Table B-5.

linkUp and linkDown Traps

Trap

What It Indicates

Possible Cause

linkDown

A failure in one of the
communication interfaces
has occurred.

A failure in one of the
communication interfaces has
occurred.

linkUp

One of the failed
communication interfaces is
up and operational.

One of the failed communication
interfaces is up and operational.

linkUp and linkDown variable-bindings are in

Table B-6

Physical and logical sublayers are represented by the entry in the MIB II
Interfaces Table. It is supported by a combination of the Frame Relay Extension
MIB and either the Frame Relay Services MIB or the Frame Relay DTEs MIB.

Summary of Contents for FrameSaver SLV 9664











































































































































































































































Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands

Paradyne FrameSaver SLV 9664, User Manual

Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands