Paradyne FrameSaver SLV 9664 User Manual Download Page 147 | Manualshive

Page: 147 / 240

background image

Troubleshooting

6-17

9664-A2-GB20-00

March 2000

Physical Tests

Physical Tests can only be commanded for the user data port.

DTE Loopback

The DTE external Loopback (DTLB) test loops the received signal on a user data
port back to the DTE. Use this test for isolating problems on the user data port.

An attached device or test equipment must generate data to be looped back.

99-16284

Network

Port

User
Data

Port

DTLB

CAUTION:

This test will affect the operation of the frame relay PVCs assigned to
the user data port. Any IP data being sent while this test is active will be
disrupted.

To start and stop a DTE Loopback:

Main Menu

→

Test

→

Data Port Physical Tests

View the length of time that the test has been running in the Result column.

«
...
145
146
147
148
149
...
»

Summary of Contents for FrameSaver SLV 9664

















































































































































































































































Reviews:

No comments

Related manuals for FrameSaver SLV 9664

SmartSwitch Router

Brand: Cabletron Systems Pages: 338

Brand: QNAP Pages: 20

Brand: Idis Pages: 16

AirBridge VS-YOFIMN-000

Brand: Vivint Pages: 2

WNR2000v2 - Wireless- N 300 Router

Brand: NETGEAR Pages: 144

BladeCenter 1/10 Gb Uplink Ethernet SwitchModule

Brand: IBM Pages: 58

Brand: Devolo Pages: 24

Brand: Zapp Pages: 24

Brand: NetComm Pages: 124

Modem/Router ADSL BIPAC-7100

Brand: Billion Pages: 13

TotalStorageFAStT900

Brand: IBM Pages: 112

Brand: 3Egreen Pages: 10

Brand: KE2 Therm Solutions Pages: 26

Brand: R.V.R. Elettronica Pages: 48

Brand: Kozumi Pages: 48

Brand: Broadrack Pages: 68

Brand: Broadcast Tools Pages: 14

2.4GHz 802.11g Wireless Outdoor Bridge NWE9251

Brand: NDC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands