manualshive.com logo in svg

Paradyne FrameSaver SLV 9664, User Manual

The Paradyne FrameSaver SLV 9664 User Manual is your comprehensive guide to effectively operating this powerful device. Obtain your free copy by easily downloading it from our website, ensuring you have all the necessary instructions at your fingertips. Empower yourself with the knowledge required to maximize the potential of your equipment.

Share
Download
background image

Security and Logins

 4-3

9664-A2-GB20-00

March 2000

"

Procedure

To limit asynchronous terminal access to the menu-driven user interface:

1. Select the Communication Port options.

Main Menu

→

Configuration

→

Management and Communication

→

Communication Port

2. Set the following configuration options, as appropriate.

To  . . .

Set the configuration option . . .

Require a login

Login Required to Enable.

NOTE: User ID and password combinations
must be defined. See 

Creating a Login

.

Limit the effective access level to
Level-3 or Level-2

Port Access Level to Level-2 or Level-3.

NOTE: Regardless of a user’s login access
level, a user cannot operate at a level higher
than the access level specified for the port
(e.g., if a user has a Level-1 login and Level-2
port access has been set, the Level-1 user
can only operate as a Level-2 user).

If you are going to allow Level-1 users to
configure the unit, keep the access at Level-1.

NOTE:

See 

Resetting the Unit  and Restoring Communication 

in Chapter 6,

Troubleshooting, should you be locked out inadvertently.

3. Save your changes.

Summary of Contents for FrameSaver SLV 9664

















































































































































































































































Reviews:

No comments

Related manuals for FrameSaver SLV 9664

D-Link ShareCenter Quattro DNS-345 Quick Install Manual preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 40
D-Link ShareCenter Quattro DNS-345 Datasheet preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 4
D-Link ShareCenter DNS-343 Quick Install Manual preview
ShareCenter DNS-343
Brand: D-Link Pages: 12
D-Link AirPlus G DWL-G710 Troubleshooting preview
AirPlus G DWL-G710
Brand: D-Link Pages: 5
D-Link MYDLINK DNR-322L Datasheet preview
MYDLINK DNR-322L
Brand: D-Link Pages: 4
D-Link mydlink DNR-312L Quick Install Manual preview
mydlink DNR-312L
Brand: D-Link Pages: 8
D-Link AC750 Quick Install Manual preview
AC750
Brand: D-Link Pages: 12
D-Link DNS-722-4 Quick Install Manual preview
DNS-722-4
Brand: D-Link Pages: 16
D-Link DNS-722-4 User Manual preview
DNS-722-4
Brand: D-Link Pages: 88
LAWO edge User Manual preview
edge
Brand: LAWO Pages: 154
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
Qlogic SANbox 6142 Supplementary Manual preview
SANbox 6142
Brand: Qlogic Pages: 2
Qlogic iSR6142 User Manual preview
iSR6142
Brand: Qlogic Pages: 172
Caen A 1735 Technical Information Manual preview
A 1735
Brand: Caen Pages: 14
ADTRAN NetVanta Analog Modem Dial Backup Interface Module Quick Start Manual preview
NetVanta Analog Modem Dial Backup Interface Module
Brand: ADTRAN Pages: 2
Zhone 6388-A2 User Manual preview
6388-A2
Brand: Zhone Pages: 53
NetBurner SBL2e User Manual preview
SBL2e
Brand: NetBurner Pages: 30
Orcon Netcom NB6 Installation preview
Netcom NB6
Brand: Orcon Pages: 2

Brands by name

Popular brands

Load more brands