Paradyne FrameSaver SLV 9664 User Manual Download Page 26

Page: 26 / 240

User Interface and Basic Operation

2-8

9664-A2-GB20-00

March 2000

Selecting from a Menu

Procedure

To select from a menu:

1. Tab or press the down arrow key to position the cursor on a menu selection,

or press the up arrow key to move the cursor to the bottom of the menu list.

Each menu selection is highlighted as you press the key to move the cursor
from position to position.

2. Press Enter. The selected menu or screen appears.

Procedure

To return to a previous screen, press the Escape (Esc) key until you reach the
desired screen.

Switching Between Screen Areas

Use Ctrl-a to switch between screen areas (see the example on

page 2-5

Procedure

To switch to the function keys area:

1. Press Ctrl-a to switch from the screen area to the function keys area.

2. Select either the function’s designated (underlined) character or

Tab to the desired function key.

3. Press Enter. The function is performed.

To return to the screen area, press Ctrl-a again.

Summary of Contents for FrameSaver SLV 9664











































































































































































































































Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands

Paradyne FrameSaver SLV 9664, User Manual

Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands