manualshive.com logo in svg

Paradyne FrameSaver SLV 9664, User Manual

The Paradyne FrameSaver SLV 9664 User Manual is your comprehensive guide to effectively operating this powerful device. Obtain your free copy by easily downloading it from our website, ensuring you have all the necessary instructions at your fingertips. Empower yourself with the knowledge required to maximize the potential of your equipment.

Share
Download
background image

Operation and Maintenance

 5-15

9664-A2-GB20-00

March 2000

Test Status Messages

These test messages appear in the right column of the System and Test Status
screen. You have the option of allowing the test to continue or aborting the test.
See Chapter 6, 

Troubleshooting

, for more information on tests, including how to

start and stop them.

Table 5-8.

Test Status Messages

Message

What It Indicates

DCLB Active, Network 1

A Data Channel V.54 Loopback (DCLB) is active
on the network interface.

DTE External LB Active, Port-1

An external DTE Loopback is running on  the user
data port.

DTE Init. Ext LB Active, Port-1

The DTE has initiated an external DTE Loopback
on the user data  port.

Lamp Test Active

The Lamp Test is active, causing the LEDs on the
faceplate to flash on and off.

Monitor

 Pttn Active, DLCI nnnn,

frame_relay_link

1, 2

The unit is monitoring a test pattern on the
specified DLCI on the specified frame relay link.

No Test Active

No tests are currently running.

PVC Loopback Active, DLCI 

nnnn,

frame_relay_link

1, 2

A PVC Loopback is active on the specified DLCI
on the frame relay link.

Send

 Pttn Active, DLCI nnnn,

frame_relay_link

1, 2

The unit is monitoring the selected test pattern on
the specified DLCI for the interface.

1

nnnn indicates a DLCI number of 16 through 1007.

2

frame relay link is one of the following:

– Net1-FR1. The frame relay link specified for the network interface, Network 1.

– Port-1. The frame relay link associated with the user data port.

Summary of Contents for FrameSaver SLV 9664

















































































































































































































































Reviews:

No comments

Related manuals for FrameSaver SLV 9664

D-Link DSL-2640BT Installation Manual preview
DSL-2640BT
Brand: D-Link Pages: 12
Makita RF1101 Parts Breakdown preview
RF1101
Brand: Makita Pages: 2
National Instruments NI 9871 Operating Instructions Manual preview
NI 9871
Brand: National Instruments Pages: 24
National Instruments NI 9478 Operating Instructions Manual preview
NI 9478
Brand: National Instruments Pages: 32
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 8
Opengear IMG4216-25 Quick Start Manual preview
IMG4216-25
Brand: Opengear Pages: 2
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Brand: Quectel Pages: 23
I-O Wireless WBC11 User Manual preview
WBC11
Brand: I-O Wireless Pages: 55
Paradyne Hotwire 6341 Installation Instructions Manual preview
Hotwire 6341
Brand: Paradyne Pages: 23
Draytek Vigor 2760 Series Quick Start Manual preview
Vigor 2760 Series
Brand: Draytek Pages: 54
TP-Link TD-8816 Quick Installation Manual preview
TD-8816
Brand: TP-Link Pages: 2
Hunter Pro-C Series Programming Instructions preview
Pro-C Series
Brand: Hunter Pages: 2
Aaeon FWS-7150 Manual preview
FWS-7150
Brand: Aaeon Pages: 57
Juniper NSM4000 Hardware Manual preview
NSM4000
Brand: Juniper Pages: 196
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
RTS AIO-8 Drawings Manual preview
AIO-8
Brand: RTS Pages: 3
Enterasys 2H258-17R Installation & User Manual preview
2H258-17R
Brand: Enterasys Pages: 62
Linksys EFG20 User Manual preview
EFG20
Brand: Linksys Pages: 37

Brands by name

Popular brands

Load more brands