Paradyne FrameSaver SLV 9664 User Manual Download Page 110 | Manualshive

Page: 110 / 240

background image

Operation and Maintenance

5-16

9664-A2-GB20-00

March 2000

Network LMI-Reported DLCIs Status

Network LMI-reported DLCI statuses are selected from the Status menu.

Main Menu

→

Status

→

LMI Reported DLCIs

The LMI Reported DLCIs screen displays the status and CIR (if supported by the
switch) for each DLCI, whether the DLCI is configured or not.

LMI-Reported DLCIs Status Screen Example

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

main/status/lmi_dlcis

9664

Device Name: Node A

05/26/1999 23:32

frame relay link

LMI REPORTED DLCIs

Page 1 of 2

DLCI STATUS

CIR (bps)

DLCI STATUS

CIR (bps)

*

300 Active

16000

*

622 Active

32000

*

305 Inactive

*

624 Active

32000

*

400 Deleted

*

625 Deleted

*

410 Inactive

*

713 Active

32000

411 Inactive

*

822 Active

32000

420 Inactive

32000

*

1002 Active

32000

430 Active

501 Inactive

511 Active

256000

520 Active

64000

* – DLCI is configured on the Frame Relay Link.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

ESC for previous menu

MainMenu

Exit

Refresh

PgUp

PgDn

NextLink

PrevLink

An asterisk (*) next to the DLCI indicates that the DLCI has been configured for
the link.

DLCIs without an asterisk have not been configured in the unit. These DLCIs
pass through the unit transparently, without being monitored and with no
demultiplexing/multiplexing of management diagnostics or user data being
performed. Only DLCIs on the Net1-FR1 and Port-1 frame relay links appear on
this screen; nonconfigured DLCIs on other links are discarded.

«
...
108
109
110
111
112
...
»

Summary of Contents for FrameSaver SLV 9664

















































































































































































































































Reviews:

No comments

Related manuals for FrameSaver SLV 9664

Brand: Eaton Pages: 10

Brand: Garmin Pages: 2

INTERNET PRIVACY PROTECTION

Brand: AlphaShield Pages: 49

Brand: Vaisala Pages: 32

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Brand: E-Lins Pages: 113

Brand: Macsense Pages: 13

JetNet 3508-LVDC

Brand: Korenix Pages: 16

Brand: Caen Pages: 14

Brand: Xantech Pages: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Brand: Juniper Pages: 122

Brand: Matrix Switch Corporation Pages: 60

Brand: F.F. Group Pages: 56

Brand: ALIBI Pages: 232

Brand: WIN Enterprises Pages: 25

Brand: Ubiquiti Pages: 2

Brand: Hamlet Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands