Paradyne FrameSaver SLV 9664 User Manual Download Page 133

Page: 133 / 240

Troubleshooting

6-3

9664-A2-GB20-00

March 2000

Resetting the Unit and Restoring Communication

You can reset the unit in one of four ways:

Reset it from the Control menu.

Cycle the power.

Reset the configuration options for the COM port, or reload the factory default
settings.

Set the appropriate MIB object from NMS (see your NMS documentation).

The unit performs a self-test when it is reset.

Resetting the Unit from the Control Menu

Use this procedure to initiate a reset and power-on self-test of the unit.

Procedure

To reset the unit from the Control menu:

1. From the Main Menu screen, select Control.

2. Select Reset Device and press Enter. The

Are You Sure?

prompt

appears.

3. Type y ( Yes) and press Enter. The unit reinitializes itself, performing a

self-test.

Resetting the Unit By Cycling the Power

Disconnecting, then reconnecting the power cord resets the unit.

Summary of Contents for FrameSaver SLV 9664











































































































































































































































Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands

Paradyne FrameSaver SLV 9664, User Manual

Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands