Paradyne FrameSaver SLV 9664 User Manual Download Page 196

Page: 196 / 240

SNMP MIBs and Traps, and RMON Alarm Defaults

B-10

9664-A2-GB20-00

March 2000

Table B-6.

linkUp and linkDown Variable-Bindings(2 of 2)

Interface

Possible Cause

Variable-Bindings

Logical Link Sublayer

Frame Relay

(Supported by the
media-specific Frame
Relay Services MIB.)

ifIndex (RFC 1573)

ifAdminStatus
(RFC 1573)

ifOperStatus (RFC 1573)

devLastTrapString
(devHealthAndStatus.-

mib)

linkDown – LMI is down for
the LMI Protocol configured,

or Frame Relay link is
disabled.

Strings:
‘$ifString down.’ No alarms
exist on the link due to LMI.

‘$ifString LMI down.’ No
alarms exist on the link
because LMI is down.

‘$ifString administratively
shutdown.’ (Due to an
intentional shutdown.)

linkUp – LMI is up or Frame
Relay link is enabled.

String:
‘$ifString up.’

If the LMI Protocol is not configured, a linkUp/ linkDown trap is based solely upon
whether the interface is enabled or disabled.

Summary of Contents for FrameSaver SLV 9664











































































































































































































































Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands

Paradyne FrameSaver SLV 9664, User Manual

Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands