manualshive.com logo in svg

Paradyne FrameSaver SLV 9664, User Manual

The Paradyne FrameSaver SLV 9664 User Manual is your comprehensive guide to effectively operating this powerful device. Obtain your free copy by easily downloading it from our website, ensuring you have all the necessary instructions at your fingertips. Empower yourself with the knowledge required to maximize the potential of your equipment.

Share
Download
background image

Troubleshooting

 6-12

9664-A2-GB20-00

March 2000

Tests Available

The following tests are available to a FrameSaver SLV 9664.

 Test Menu Example

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

main/test

 9664

Device Name: Node A

 5/26/1999 23:32

TEST

Network PVC Tests

Data Port PVC Tests

Data Port Physical Tests

IP Ping

Lamp Test

Abort All Tests

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Ctrl-a to access these functions, ESC for previous menu

MainMenu

Exit

PVC Tests menu selections are suppressed when no PVCs have been configured
on the interface. Check that both ends of the cables are properly seated and
secured.

Tests can be commanded from the OpenLane 5.

x management solution using its

Diagnostic Troubleshooting graphical interface, as well as from the menu-driven
user interface.

Test Timeout Feature

A Test Timeout feature is available to automatically terminate a test (as opposed
to manually terminating a test) after it has been running a specified period of
time.

It is recommended that this feature be used when the

 

FrameSaver unit is

remotely managed through an inband data stream (PVC). If a test is accidently
commanded to execute on the interface providing management access, control is
regained when the specified time period expires, automatically terminating the
test.

To use this feature, enable the Test Timeout configuration option, and set a
duration for the test to run in the Test Duration (min) configuration option (see

Configuring General System Options 

in Chapter 3,

 

Configuration).

Summary of Contents for FrameSaver SLV 9664

















































































































































































































































Reviews:

No comments

Related manuals for FrameSaver SLV 9664

Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Brand: Panasonic Pages: 2
Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
Patton electronics SMART NODE 4950-NCE Quick Start Manual preview
SMART NODE 4950-NCE
Brand: Patton electronics Pages: 8
Patton electronics NetLink 2960 RAS Datasheet preview
NetLink 2960 RAS
Brand: Patton electronics Pages: 2
Patton electronics 3101RC Specifications preview
3101RC
Brand: Patton electronics Pages: 2
Qlogic iSR6200 Quick Start Manual preview
iSR6200
Brand: Qlogic Pages: 20
Niveo NWAR33P User Manual preview
NWAR33P
Brand: Niveo Pages: 155
Premio FlacheSAN1L-D4 Quick Manual preview
FlacheSAN1L-D4
Brand: Premio Pages: 3
process-informatik CONNECT Series Operation Quick Start Manual preview
CONNECT Series
Brand: process-informatik Pages: 8
RuggedCom RUGGEDSWITCH RS900G Hardware Installation Manual preview
RUGGEDSWITCH RS900G
Brand: RuggedCom Pages: 23
Tbus NV-ER1816i Installation Manual preview
NV-ER1816i
Brand: Tbus Pages: 25
Faderfox 4midiloop User Manual preview
4midiloop
Brand: Faderfox Pages: 10
Gemtek Systems WLTFQR-121 User Manual preview
WLTFQR-121
Brand: Gemtek Systems Pages: 51
RubyTech VS-820S User Manual preview
VS-820S
Brand: RubyTech Pages: 25
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
Idis DR-1500 Series Quick Manual preview
DR-1500 Series
Brand: Idis Pages: 17
Planet IGS-5225-20T4C2X Quick Installation Manual preview
IGS-5225-20T4C2X
Brand: Planet Pages: 16
Ovislink Air Live GW-300R User Manual preview
Air Live GW-300R
Brand: Ovislink Pages: 20

Brands by name

Popular brands

Load more brands