Paradyne FrameSaver SLV 9664 User Manual Download Page 157

Page: 157 / 240

Setting Up NetScout Manager Plus for FrameSaver Devices

8-5

9664-A2-GB20-00

March 2000

Verifying Domains and Groups

Procedure

1. From the NetScout Manager Plus main window, with the FrameRelay and

Admin radio buttons still selected, click on the Config Manager icon to open
the Configuration Manager main window.

2. Verify that only FrameSaver SLV-supported domains appear listed in the

Domain column. FrameSaver SLV-supported domains include:

— ATALK

— IPX

— RMON

— DECNET

— NETB

— SNA

— IP

— NET~

— VINES

— IPV6

— OSI

3. Verify that:

— S (statistics collection) appears for each domain listed in the Group

column.

— H (hosts) appears for the IP domain only.

— Dashes occupy all other positions under the Group column.

— Zeros appear under the Samples and Interval SH and LH columns.

— Dashes appear under all Logging columns: Stat, Host, Conv.

4. If all these requirements are met, no further action is required. Close the

Configuration Manager window.

If all these requirements are not met, a FrameSaver SLV-supported domain
needs to be added, or if an unsupported domain needs to be deleted, the
Properties File must be edited.

Summary of Contents for FrameSaver SLV 9664











































































































































































































































Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands

Paradyne FrameSaver SLV 9664, User Manual

Search results

Summary of Contents for FrameSaver SLV 9664

Reviews:

Related manuals for FrameSaver SLV 9664

Brands by name

Popular brands