manualshive.com logo in svg

Paradyne FrameSaver SLV 9664, User Manual

The Paradyne FrameSaver SLV 9664 User Manual is your comprehensive guide to effectively operating this powerful device. Obtain your free copy by easily downloading it from our website, ensuring you have all the necessary instructions at your fingertips. Empower yourself with the knowledge required to maximize the potential of your equipment.

Share
Download
background image

Setting Up NetScout Manager Plus for FrameSaver Devices

 8-15

9664-A2-GB20-00

March 2000

Installing the User-Defined History Files

Once the user-defined history files have been created, the files need to be
installed. History files are installed from the command-line prompt in NetScout
Manager Plus. Should the FrameSaver unit be reset, these files will need to be
reinstalled. The command used to install a new user history table is located in
$NSHOME/bin.

CAUTION:

Do not use user_history_table_1 or 2.  UserHistory1 and UserHistory2
are the default user history files used to keep SLV data for reports.
Editing either of these files will destroy SLV reporting capability.

"

Procedure

1. Type dvuhist -f 

agentname user_ history_ table_ number config

number_of_buckets interval download_ file.udh to load user-defined history

files for the frame relay link.

Example:  

dvuhist -f Dallas51 3 config 30 60 Dallas51k.udh

The interval must be entered in seconds.

2. Type dvuhist -f 

“agentname  DLCI_ number”

 

 user_ history_ table_ number 

config

  number_of_buckets  interval  download_ file.udh to load user-defined

history files for a specific DLCI.

Example:  

dvuhist -f “Dallas51 301” 3 config 30 60 Dallas301.udh

The same user history table number can be used for both the link and DLCI.
For these examples, user history table number 3 will appear as UserHistory3
on the History List.

See 

Step 5

 in 

Monitoring a DLCI’s History Data to verify that the user-defined

history files have been loaded.

Refer to 

Installing .UDH Files in Using Custom History of the NetScout Manager

Plus User Guide for additional information.

Summary of Contents for FrameSaver SLV 9664

















































































































































































































































Reviews:

No comments

Related manuals for FrameSaver SLV 9664

Qixiang Technology QR310 Installation And Configuration Quick Manual preview
QR310
Brand: Qixiang Technology Pages: 16
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Lanner NCA-1040 User Manual preview
NCA-1040
Brand: Lanner Pages: 59
Dahua NVRPRO User Manual preview
NVRPRO
Brand: Dahua Pages: 113
Firetide HotPort 3103 User Manual preview
HotPort 3103
Brand: Firetide Pages: 32
Mobatime DTS 4020.timebridge Mounting And Instruction Manual preview
DTS 4020.timebridge
Brand: Mobatime Pages: 94
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
Tripp Lite N002-025-RD Specification Sheet preview
N002-025-RD
Brand: Tripp Lite Pages: 3
Alloy POEGE24T User Manual preview
POEGE24T
Brand: Alloy Pages: 13
VAMISOUND Schoeps electret Building Instructions preview
Schoeps electret
Brand: VAMISOUND Pages: 15
Umniah 3G Evo Router User Manual preview
3G Evo Router
Brand: Umniah Pages: 12
Tripp Lite N304-025 Specification Sheet preview
N304-025
Brand: Tripp Lite Pages: 2
LOOQS MB202 User Manual preview
MB202
Brand: LOOQS Pages: 69
LOOQS MeeBox MB201 User Manual preview
MeeBox MB201
Brand: LOOQS Pages: 76
NetApp NS224 Instructions Manual preview
NS224
Brand: NetApp Pages: 28
Tripp Lite N302-010 Specification Sheet preview
N302-010
Brand: Tripp Lite Pages: 2
Robustel GoRugged R3000 Lite Quick Start Manual preview
GoRugged R3000 Lite
Brand: Robustel Pages: 8
Proscend 5200N Series User Manual preview
5200N Series
Brand: Proscend Pages: 55

Brands by name

Popular brands

Load more brands