45
44
9
9
SPA MAINTENANCE
Your Pacific Spa is manufactured from the highest quality materials available. The spa care and maintenance program you
develop will ultimately determine how long your spa and its individual components will last. Regular maintenance following the
advice in this section will help you to protect your investment.
Spa Shell
Your Pacific Spa has a fibreglass reinforced, acrylic shell. Stains and dirt generally will not adhere to your spa’s surface. A soft cloth
or sponge should easily remove most dirt. Most household chemicals are harmful to your spa’s shell. It is important that you do
not use any abrasive cleaners or strong chemicals. Your local Pacific Spa dealer will be able to supply you with the proper cleaning
solution for your spa. After cleaning, ensure all residue is removed prior to filling the spa. This will help prevent sudsing and
improper chemical balance. Sodium bicarbonate (baking soda) or vinegar can also be used for minor surface cleaning. Always
thoroughly rinse off any cleaning agent with fresh water.
Filtration System
As with any water filtering system, the filter cartridge may become clogged, resulting in reduced water flow. It is important to
maintain a clean, unobstructed filter system.
Filter cartridge removal and installation:
1. Shut the spa down or set spa to standby.
2. Remove and set aside the filter cover.
3. Remove the filter basket by rotating the top outside ring counter-clockwise and lift.
4. Remove the filter cartridge.
5. Clean any debris from the skimmer basket.
6. Rinse and soak the cartridge.
7. To reinstall the filter cartridge, reverse the order of the steps in which it was removed.
Jets
Your jets should be removed and cleaned when you drain your spa to clean any sand or grit from the bearings and remove any
blockage from the entrance port. Cleaning should be done in hot soapy water or dishwashing detergent. Ensure that the jet is
moving freely before reinserting it. You can turn the jet on or off by rotating the jet face clockwise or counter-clockwise.
To remove the jet inserts:
1. Turn the jet to the off position until it stops.
2. Turn the jet past the stop point.
3. Pull the jet insert away from the spa.
When inserting a jet, match the opening on the jet housing wall to the U-shaped cut out on the end of the diffuser and push the
jet in flush until resistance is felt, then continue to push the jet flush and forward until it snaps into place. Using this procedure will
reduce the wear on your jets and increase their longevity.
Skirting
Cedarlite synthetic wood skirting consists of a rigid polymer which combines
the durability of plastic with the beauty of wood. Cedarlite won’t crack, peel,
blister or delaminate even after prolonged exposure to the elements. Cleaning
of Cedarlite consists of simply spraying the cabinet with a mild soap and water
solution to remove any stains and residue. Screws at the base of the panel
fasten each panel in place. The screws holes are slightly oversized to allow
the panel to adjust to the weight of the water in a filled spa. If an adjustment is
needed, the screws can be loosened and the panel will adjust to the weight of
the water. Over tightening or failure to adjust the screws may cause the skirting
to buckle. You can remove the threaded screw cap covers by turning them
counter-clockwise.
note
:
Use caution when installing cover lifters. To avoid damage to the panel,
ensure the screw holes are pre-drilled and the supporting panels are adequately
braced with a 2 x 4 wall stud before mounting the cover lifter. Avoid penetrating
the plumbing lines with bracing screws, as this may create leaks in the lines
(you can see any damage by removing the panel). Do not allow the cover lifter to
fall under its own weight as this may damage the side panel. Carefully brace the
cover lifter when opening or closing the cover. Any damage caused by a cover
lifter attached to the spa is not covered by warranty.
Care of Spa Pillows
To extend the life of the pillows, they should be removed and cleaned whenever the spa shell is being cleaned. Body oils can be
removed with a mild soap and water solution. Always rinse the spa pillows thoroughly to remove any soap residue. Remove the
pillows from the spa for extended periods of non-use.
Further care for spa pillows:
∙ Do not sit on pillows.
∙ Do not pull on pillows.
∙ Proper water chemistry must be maintained.
∙ When you shock your spa, remove your cover, pillows and filter lid for a minimum of 30 minutes so excess gases may escape
from the spa.
Pump Seal
Your jet pump is built using a “wet end” pump and a “dry end” motor with a seal in the middle. Depending on use and chemical
balance, this seal will eventually need replacing. Check your motor monthly to ensure there is no water leaking to the motor area.
If you detect any signs of leakage, contact your dealer immediately.
