5
5
35
34
6
6
After a few seconds the available networks will appear
on the screen, as well as their signal strength.
Use the Up/Down keys to move through the list.
Select your network by pressing on Light key.
If the WiFi network is password protected enter it
when prompted.
∙ Use the arrow keys to choose your letters and
change the type of character (uppercase,
lowercase, number, symbol)
∙ Use Key 2 to move the cursor forward
∙ Use Key 1 to backspace
∙ Use Light key to confirm
If no password is required, the in.touch will connect
automatically.
Once the in.touch module is connected to a WiFi
network, a check mark in a green circle will appear
in the WiFi menu and the network logo will change to
green in the Settings menu.
Note: The WiFi logo colour in Settings menu
corresponds to the in.touch connection state.
Yellow = not connected
Green = connected to a network
Yellow with wait icon = connection attempt to a
network
Red with wait icon = in.touch no longer detected
(in.touch must be reset before next connection
attempt)
in.clear
in.clear-200 / Linked Version
(version 13.00
and higher)
The in.k500 keypad can be used with the in.clear
sanitization system. The in.clear section allows you to
configure your maintenance settings and Boost level.
For more information on maintenance and Boost
settings, see the in.clear user manual.
Use the Up and Down keys to make your selection,
then the Light key to confirm.
Use the Up and Down keys to change the
maintenance or Boost value and light key to confirm.
Note: If the maintenance value is modified by more
than “2”, a warning message will appear with an
option to cancel or confirm the change.
Press on the Mode key to access your in.clear
module.
This menu allows you to activate or deactivate
your in.clear, to start or stop a Boost and to enter
diagnostic mode.
Turning the in.clear On/Off
Press the power key to turn the in.clear on or off.
Control the Boost Level
Press on the Boost activation/deactivation key to start
a Boost, and again to cancel.
To adjust the Boost level use the arrow keys.*
A message indicating that Boost mode is active is
displayed at the bottom of the main screen for the
duration of the Boost.
* See the in.clear user manual for more details about
Boost levels.
Diagnostic Mode
Press on the Diagnostic key to start a BromiCharge
concentration level test. To exit diagnostic mode
press on the Diagnostic key again. The system will
automatically exit after15 minutes.
In diagnostic mode, the BromiCharge gauge indicates
the approximate level of BromiCharge in the spa
water. Do not add BromiCharge if the indicator is in
the green zone.
When BromiCharge is added, the indicator will move
slowly to the right. When water is added to the spa the
indicator will move to the left. To obtain a good level of
BromiCharge, start the pumps and add the specified
amount of BromiCharge* and allow five minutes for
the indicator to adjust before adding more.
For optimal performance, aim for the middle of the
green zone.
* For more information on adjusting your
BromiCharge level, see the in.clear user manual.
WiFi
(version 7.00 and higher)
For the WiFi menu to appear in the Settings menu
your in.touch module must be equipped with software
version 11.00 or higher. This menu allows you to
connect your in.touch module to a WiFi network or to
change its network.
For more details about other in.touch connection
methods, please see the in.touch Techbook.
To connect your in.touch module to a wireless
network, use the Up/Down keys to go to the WiFi
option in the Settings menu and Light key to select it.
WiFi (in.touch Only)
in.mix
in.mix Operation
This menu is only present if an in.mix system is
detected.
Press on the Mode key to access your in.mix.
By default, the in.mix selects Zone 1 when you
access the menu. After the first use, the menu will
automatically return to the last zone selected.
Zone Selection
The zone selection keys allow you to select a zone to
modify its colour.
∙ Press once to select the zone
∙ Press a second time to deactivate the zone
Changing Colours
Once a zone is selected, use the arrow keys to change
the colours by moving up and down in the colour
wheel.
Synchronizing Zones
The synchronization/desynchronization key allows you
to match the colour of the selected zone to the other
zones.
9919-1012012-K
Rev. 02-2020
www.geckoalliance.com
© Groupe Gecko Alliance Inc., 2020
All trademarks or registered trademarks are the property of their respective owners.
Printed in Canada
