41
40
8
7
Spa Cover
This is a user serviceable part
A vinyl cleaner should be used regularly on your thermal cover. This will help guard against the sun’s damaging ultraviolet rays and
help to prevent mildew stains. We recommend a periodic treatment of non-silicone spray for outdoor covers to help repel rainwater.
We also recommend that every six months you remove the cover inserts to allow them to air out. Do not allow snow to build up on
the cover. Never allow anyone to stand or sit on the cover. Avoid dragging the cover across rough surfaces.
The underside of your spa cover is a good reflection of the condition of your water. Poor water balance will quickly change the
colour and texture of the cover’s underside. It can also minimize the life expectancy of your spa cover. Please take steps to correct
any water chemistry problems quickly to avoid serious damage to your cover. Even with perfect water balance, it is recommended
that you wash the inside of your cover on a monthly basis to remove any chemical residue.
note
:
When adding more than the normal daily amount of disinfectant (i.e. shock treatment) leave the spa cover off for a minimum
of one hour. Failure to do so could damage the under side of the cover and void the warranty.
Generally, the greatest amount of damage and wear to the cover happens when removing or reinstalling the cover during use.
During hot weather, the vinyl becomes very susceptible to cutting and tearing along the seams. The use of a cover removal device
is recommended to reduce much of this damage.
note
:
It is normal to expect some fading or discolouration to occur over time.
Inside the vinyl cover are two insulating cores. These cores are accessed by folding the cover in half and unzipping the side. Care
must be taken in removing the cores so as not to damage the vinyl casing. Over time, it is expected that the cores will become
saturated and heavy. In this case, replacement insert cores can be ordered from your Pacific Spas dealer.
note
:
Use caution when installing cover lifters. To avoid damage to the panel, ensure the screw holes are pre-drilled and the
supporting panels are adequately braced with a 2 x 4 wall stud before mounting the cover lifter. Avoid penetrating the plumbing
lines with bracing screws, as this may create leaks in the lines (you can see any damage by removing the panel). Do not allow the
cover lifter to fall under its own weight as this may damage the side panel. Carefully brace the cover lifter when opening or closing
the cover. Any damage caused by a cover lifter attached to the spa is not covered by warranty.
OPTIONAL COMPONENTS
In.stream Bluetooth Stereo System
Everything you need to know about the in.stream 2 audio
station Bluetooth function.
Bluetooth Range
The range of the Bluetooth module installed in the in.stream 2
is approximately 10 metres (32.8 feet), but the practical range
depends on geographic, atmospheric and urban conditions.
Any obstacle such as the insulation of the spa skirt, a wall or
a body of water can reduce its range significantly. Therefore,
it is important not to be too far from the station when trying to
establish a Bluetooth connection.
In order to maximize the effective range of the Bluetooth, the
in.stream 2 should be installed facing an open area and in a
way that it will have a clear line of sight with the devices being
used to stream music.
Connecting to the Audio Station
The Bluetooth connection is done in two steps. Before they can connect together, the devices being used need to be paired.
To pair or connect any device to the in.stream 2 audio station, the station must be open and must not be connected to any other
device via Bluetooth, as it is impossible to interrupt one connection to establish a new one.
Pairing
In order to pair a device with the in.stream 2 station, you will need to access the Bluetooth settings of that device. From there,
some devices will automatically search for other nearby Bluetooth devices while the "search" function will have to be activated on
other devices.
Once the in.stream 2 has been detected by your device, select it to initiate the pairing process. When asked for a password, type in
"5555" to complete the pairing. Once paired, the devices can connect together.
At this point, your device will be paired with the in.stream 2 and it will be possible to reconnect it to the station, automatically or
manually, without having to pair it again, as long as the pairing between both devices isn't deleted.
The in.stream 2 can be paired with a total of eight different devices, but it can only maintain one connection at a time. If eight
devices are paired with the station already, the next device to be paired will cause the station to delete the device that was used for
the longest time from its pairing list so it can complete the new pairing request.
Connection
To manually connect an already paired device to the audio station, open the Bluetooth settings of the device you want to connect
and select "in.stream 2" from its list of paired devices. However, be advised that the list of paired devices usually displays every
piece of equipment paired with your device, even if they are not available for a connection. Thus, ensure you are near the
in.stream 2 and that the station isn't already connected to another Bluetooth device, otherwise the connection attempt will fail and
your device will return an error message.