manualshive.com logo in svg

OTARI Status 18R, Operation And Maintenance Manual, Page: 101 / 250

Share
Download
OTARI Status 18R Operation And Maintenance Manual Download Page 101

4.11 Solo System

4.11.1 Introduction

The STATUS 18R allows independent selection of Solo modes for the Channel and Mix
paths. The buttons for controlling these modes are located in the LCD Display section of
the Digital Master module. A number of options are available in UPS that change the way
the Solo system operates.

4.11.2 Solo Modes

Two types of Solo are available on the STATUS 18R, In-Place Solo (IPS) and Monitor
Interrupt Solo (MIS). Each has its advantages and disadvantages in a given application.

NOTE: 

The term “IPL” (In-Place Listen) is sometimes used in place of “IPS” when

defining In-Place Solo. The terms are identical and can be used interchangibly.

■

In Place (IPS)

In Place Solo means that when a path is soloed, it remains in place in the Stereo image.
This happens because all unsoloed paths are actually muted while the path is soloed.
For this reason, In-Place solo is called a “destructive” solo, meaning that program output
of the console changes as paths are muted during the solo operation.

Because it is “destructive”, IPS soloing would not be a wise choice during music
recording or a broadcast. Executing a solo could mute channels in the cue headphones
or the program feed. IPS soloing is useful during mixing, however, because an
instrument can be soloed with effects exactly as it is heard in the mix.

■

Monitor Interrupt (MIS)

Monitor Interrupt Solo is “non-destructive”. A separate Solo bus in the console sums all
soloed paths. When a solo is executed, the Control 

Room section temporarily selects this Solo Bus for monitoring. No channels are muted.

paths soloed by MIS soloing can be sourced Pre (PFL or Pre Fader Listen) or Post (AFL
or After Fader Listen) the path’s fader. If set to AFL, soloed paths are in Stereo, as
defined by the path’s pan pot. If set to PFL, soloed paths are in mono. PFL soloing
allows a path to be soloed while the fader is down so that it can be raised on cue. AFL
soloing preserves the mix relationship when multiple channels are soloed.

Because of its non-destructive nature and PFL function, MIS soloing is ideal for
broadcast and tracking purposes. For mixing however, IPS soloing is usually more
desirable than MIS soloing.

Section 4 - Operation

August 1999

4 - 19

STATUS 18R 

Operation and Maintenance Manual

EQ

On

Solo

Mute

Soft

Meter

Solo

Group

Recall

Automation

Misc

MIXIP CHANIP  AFL   PFL 
DEFEAT ADD  INTRLK MOMEN

Solo LCD Menu

Path Solo Button

Summary of Contents for Status 18R



























































































































































































































































Reviews:

No comments