manualshive.com logo in svg

NXP Semiconductors i.MX 6Dual, Reference Manual

Share
Download
NXP Semiconductors i.MX 6Dual Reference Manual Download Page 83

ERR009743

Chip Errata for the i.MX 6Dual/6Quad and i.MX 6DualPlus/6QuadPlus, Rev. 6.1, 06/2016

NXP Semiconductors

83

 

Description:

DBGPRSR.SR, bit [3], is the Sticky Reset status bit. The ARM architecture specifies that the 
processor sets this bit to 1 when the non-debug logic of the processor is in reset state.
Because of this erratum, the Cortex-A9 processor sets this bit to 1 when the debug logic of the 
processor is in reset state, instead of when the non-debug logic of the processor is in reset state.

Projected Impact:

- DBGPRSR.SR might not be set to 1 when it should, when the non-debug logic of the processor 
is in reset state.
- DBGPRSR.SR might be set to 1 when it should not, when the debug logic of the processor is in 
reset state.
In both cases, the DBGPRSR.SR bit value might be corrupted, which might prevent the debug 
logic from correctly detecting when the non-debug logic of the processor has been reset.

Workarounds:

No software workaround available as this erratum is related to a debug feature. Users should not 
rely on the DBGPRSR.SR bit during the debug session.

Proposed Solution:

No fix scheduled

Linux BSP Status:

Software workaround is not implemented because this erratum will never be encountered in normal 
device operation, as this erratum is related to a debug feature.

ERR009743

ARM: 799770 - DBGPRSR Sticky Reset status bit is set to 1 by the CPU 
debug reset instead of by the CPU non-debug reset

Summary of Contents for i.MX 6Dual


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands