manualshive.com logo in svg

NXP Semiconductors i.MX 6Dual, Reference Manual

Share
Download
NXP Semiconductors i.MX 6Dual Reference Manual Download Page 153

ERR004297

Chip Errata for the i.MX 6Dual/6Quad and i.MX 6DualPlus/6QuadPlus, Rev. 6.1, 06/2016

NXP Semiconductors

153

 

Description:

The core moves ahead even when it does not receive the same non-PAD lane number in two 
consecutive TS Ordered Sets (OS) in the Link configuration process. 

Scenario Setup: 

• The link is in the link training phase. 

• Remote partner sends TS OS without the same non-PAD lane number in any two consecutive 

TS OS on any active lane. 

• The core moves ahead regardless of the non-PAD lane number not being the same in two 

consecutive TS OS.

Projected Impact:

This violates PCIe Base Specification “two consecutive TS Ordered Sets are received”. The core 
moves ahead without robustness to the Link configuration process.

Workarounds:

None. This issue will not lead to any compliance failures.

Proposed Solution:

No fix scheduled

Linux BSP Status:

Software workaround cannot be implemented to mask or workaround this SoC issue. This erratum 
will result in impacted or reduced functionality as described above.

ERR004297

PCIe: 9000336356—Link configuration sometimes proceeds when 
incorrect TS Ordered Sets are received

Summary of Contents for i.MX 6Dual


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands