manualshive.com logo in svg

NXP Semiconductors i.MX 6Dual, Reference Manual

Share
Download
NXP Semiconductors i.MX 6Dual Reference Manual Download Page 217

ERR004364

Chip Errata for the i.MX 6Dual/6Quad and i.MX 6DualPlus/6QuadPlus, Rev. 6.1, 06/2016

NXP Semiconductors

217

 

Description:

uSDHC3 and uSDHC4 clock-gating controls (CG and MOD_EN_OV) in CCM are gating 
RAWNAND and APBADMA clocks.

• apbhdma.hclk controlled by usdhc3_clk_root CGR

• rawnand.u_bch_input_apb_clk controlled by usdhc3_clk_root CGR

• rawnand.u_gpmi_input_apb_clk controlled by usdhc3_clk_root CGR

• rawnand.u_gpmi_bch_input_bch_clk controlled by usdhc4_clk_root CGR

Projected Impact:

RAWNAND and APBHDMA clocks might be gated unintentionally.

Workarounds:

uSDHC3 and uSDHC4 clock-gating controls should not be configured to gate the clocks in case 
RAWNAND and APBADMA are used. There are two registers in CCM that need to be configured 
accordingly:

• CCGR: Gating of the clock according to power mode

• CMEOR: Enable/Disable dynamic clock gating

Proposed Solution:

No fix scheduled

Linux BSP Status:

Software workaround not implemented in Linux BSP. Functionality or mode of operation in which 
the erratum may manifest itself is not used.

ERR004364

uSDHC: Limitations on uSDHC3 and uSDHC4 clock-gating

Summary of Contents for i.MX 6Dual


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands