Nussbaum BT 610, Operating Instructions Manual

Page: 86 / 96

86 26.11.07 1 689 979 924N
Error code 17 05 *
Measuring board of the wheel tester outside of the zero position.
The measuring board does not return to the home positon (saved
zero position) after the axle has been measured.
Cause:
- Measuring board of the wheel tester has not yet been
calibrated.
- Springs in the measuring board defective
- Measuring board has been keyed mechanically.
Error code 17 10 *
No signal from wheel tester limit switch.
Cause:
- Wheel tester set has been activated in the configuration
menu, but does not exist physically.
- Sensor line defective.
- Limit switch defective
15.8 Error wheel suspension tester
Error code 18 00
No signal wheel suspension tester left-hand side.
Cause:
- Wheel suspension tester set has been activated in the
configuration menu, but does not exist physically.
- Wheel suspension tester left-hand side defective.
- Sensor line defective.
Error code 18 01 *
When switching on, no cal-check-function of the wheel suspen-
sion tester on the left-hand side.
Cause:
- Wheel suspension tester set has been activated in the
configuration menu, but does not exist physically.
- Sensor line defective.
- Cal-check-line interrupted (wire breakage)
Error code 18 02 *
Wheel suspension tester left-hand side has not yet been calibra-
ted.
Error code 18 05 *
When switching on, zero point wheel suspension tester left-hand
side from EEPROM compares to current force. In case of a
difference > 500 N, the error is displayed.
Cause:
- Wheel suspension tester right-hand side defective.
- Wheel suspension tester sensor has not yet been calibrated.
- When switching on, a vehicle or an object is located on the
measuring board
Error code 18 10
No signal wheel suspension tester right-hand side
Cause:
- Wheel suspension tester set has been activated in the
configuration menu, but does not exist physically.
- Wheel suspension tester right-hand side defective.
- Sensor line defective.
Error code 18 11 *
When switching on, no cal-check-function of the wheel suspen-
sion tester on the right-hand side.
Cause:
- Wheel suspension tester set has been activated in the
configuration menu, but does not exist physically.
- Sensor line defective.
- Cal-check-line interrupted (wire breakage)
Error code 18 12 *
Wheel suspension tester right-hand side has not been calibrated.
Error code 18 15 *
When switching on, zero point wheel suspension tester right-
hand side from EEPROM compares to current force. In case of a
difference > 500 N, the error is displayed.
Cause:
- Wheel suspension tester right-hand side defective.
- Wheel suspension tester sensor has not yet been calibrated.
- When switching on, a vehicle or an object is located on the
measuring board
Error code 18 20 *
One or two wheel weights to be inspected > 1000kg. In order to
avoid a defect, the measurement is not started.
Error code 18 30 *
One or two wheels to be inspected have been rolled out of the
center of the measuring board during the measurement.
15.9 Error on the PCB
Error code 19 00
Power supply 12V DC for sensors not available
Cause:
- Printed circuit board A1 defective.
- Short-circuit on a sensor line
Error code 19 10
Reference voltage VREF not available on PCB A1. This voltage is
necessary for the correct functioning of the AD converter.
Cause:
- Printed circuit board A1 defective.
Error code 19 20
24 V AC for contactor control not available.
Cause:
- Printed circuit board A1 defective.
- Fusible cut-out F2 defective.
- Transformer T1 defective.
Error code 19 30 *
No CAN-bus communication possible underneath the PCBs.
Cause:
- A PCB defective.
- CAN terminating resistors not available.
- CAN line defective.
Error code 19 40 *
Coin cell (battery) on PCB A1 not available or empty.