NuAire LabGard NU-560-400 Operation & Maintenance Manual Download Page 86

Page: 86 / 103

OM0295

Rev 2 September 2020

Page 86 of 103

•

Fan Relay interlock:

This parameter allows for the selection of the fan relay interlock operation. When

the fans relay interlock is on, and the blower switch is pending or blue, the fan relay will be off or not

energized. If the fan relay interlock is off and the blower switch is pending or blue, the fan relay will be

on or energized. In either case the fan relay will be on when the blower switch is on or green and off

when the blower switch is off or not colored.

•

Blower FL Light Interlock:

This parameter allows for the selection of the FL light option to be

interlocked to the blower. When the blower FL light interlock is on, the FL light operation will be

interlocked to the blower. When the blower FL light interlock is off, the FL light can be turned on at any

time.

Summary of Contents for LabGard NU-560-400








































































































Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands

NuAire LabGard NU-560-400, Operation & Maintenance Manual

Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands