NuAire LabGard NU-560-400 Operation & Maintenance Manual Download Page 70

Page: 70 / 103

OM0295

Rev 2 September 2020

Page 70 of 103

8.0

Error Messages, Troubleshooting, Option-Diagnostics & Airflow Sensor Performance Verification

Audible alarms and error messages occur for a variety of reasons. Whenever an alarm condition has been present for a

period of at least 10 seconds, the audible alarm/error message will be presented and stay on until the error is cleared. The

audible alarm will be on for 30 seconds upon initial alarm condition, then once every ten seconds. When presented with an

error message, please perform the following:

Step 1: NOTE ALL ERROR MESSAGES.

Error message will appear in place if the NuAire logo with “Active Alarms” and the alarm type below.

Step 2: VERIFY ERROR MESSAGES.

Error messages can be verified by cleaning the error function by either turning the blower

or the cabinet on and off.

Step 3: MONITOR RE-OCCURRENCE OF ERROR MESSAGES.

If re-occurrence of the error message is immediate or daily, use guide below to correct the situation.

Summary of Contents for LabGard NU-560-400








































































































Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands

NuAire LabGard NU-560-400, Operation & Maintenance Manual

Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands