NuAire LabGard NU-560-400 Operation & Maintenance Manual Download Page 87

Page: 87 / 103

OM0295

Rev 2 September 2020

Page 87 of 103

•

Blower Outlet Interlock:

The blower/outlet interlock turns on/off the outlets whenever the blower is

turned on/off. The outlet power can no longer be controlled manually



Auxiliary Features

This menu item provides the access to aux relay function and accessory outlet functions

•

Aux Relay function

: This parameter allows for the selection of the AUX relay function. When the AUX

relay is on, the AUX relay function will be identical to the fan relay. When the AUX relay function is off,

the AUX relay function provides delay ON/OFF option.

•

Accessory Outlet

: this parameter allows to turn ON and OFF the accessory outlet.

Summary of Contents for LabGard NU-560-400








































































































Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands

NuAire LabGard NU-560-400, Operation & Maintenance Manual

Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands