NuAire LabGard NU-560-400 Operation & Maintenance Manual Download Page 82

Page: 82 / 103

OM0295

Rev 2 September 2020

Page 82 of 103

8.2.2.3 Option Setup

The option set up menu allows

A QUALIFIED TECHNICIAN

to configure several different optional parameters per

the menu below. Each parameter sub-menu will be described as well as the display will the default conditions as

shown

•

Alarm Setup

•

Alarm Silence:

This parameter allows for the selection of the alarm silence key function. When the

alarm silence function is on, all current and future alarms will be silenced for the designated alarm

silence time (i.e. default time is 15 minutes). When the alarm silence function is off, all current alarms

will be silenced for the designated alarm silence time. If a new alarm is present, the audible alarm will

again be turned on.

Summary of Contents for LabGard NU-560-400








































































































Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands

NuAire LabGard NU-560-400, Operation & Maintenance Manual

Search results

Summary of Contents for LabGard NU-560-400

Reviews:

Related manuals for LabGard NU-560-400

Brands by name

Popular brands