Ness SmartLiving 10100 Installation & Programming Manual Download Page 79 | Manualshive

Page: 79 / 112

background image

Installation and programming manual

Options and programming methods

79

6-19

Expansions

This section allows you to programme the parameters of the expansions.

Via Keypad

Type-in Code

(Installer PIN)

, PROGRAMMING Expansions

.

Enable/disabl

e

This section allows you to add/remove expansions from the I-BUS configuration, by
means of keys

and

.

ChoosePeripheral

This section allows you to edit the description of each expansion board.

Via PC

6-20

Keypads

This section allows you to programme the parameters of the keypads.

Via Keypad

Type-in Code

(Installer PIN)

, PROGRAMMING Keypads

.

Enable/disable

This section allows you to add/remove expansions from the I-BUS configuration, by
means of keys

and

.

ChoosePeripheral

This section allows you to programme the various options of the selected keypad.
•

Description

- editable field for the name of the digital key user.

•

Partitions

- use

and

to enable/disable the keypad on the system

partitions.

•

Options

:

••

Temperature off

- (Temp available on Alien Keypads only). if this option is

enabled, the room temperature will be flashed in alternation on the display. This
option is valid for keypads with built-in temperature sensors only.

••

SilentExitTime

- enables/disables the buzzer during partition Exit Time.

••

SilentEntryTime

- enables/disables the buzzer during partition Entry time

••

SignalExitTime

- enables/disables the buzzer when terminal T1 on the keypad is

activated as an output.

•

F1/4KeyShortcuts

- setting of the shortcuts assigned to keys

, ...,

.

If you are programming an Alien keypad, this shortcut refers to the position in the
list available in the “Scenarios” section of the Alien keypad you are working on.
Function keys F1 to F12 must be selected separately and programmed as follows:
••

Type

- this is the shortcut action which can be selected from those available

(refer to

Appendix B, Shortcuts at default

). It is necessary to programme an

extra parameter for some shortcuts:

-

“Arm/disarm”, this parameter refers to one of the 30 scenarios

-

“Activate outputs”, this parameter refers to the output that will be deactivated

-

“Deactiv. outputs”, this parameter refers to the output that will be deactivated

Note

The “Listen-in” and “Arming status” will have no effect if the respective command is entered at a
keypad.
If you are programming an Alien keypad, the only type of shortcut that functions is “Arm/disarm”.

••

Options

- activated by means of keys

and

, are:

-

Requires code

- if enabled, the system will ask for user-code entry before

activating the shortcut. If the system recognizes the entered user code, it
will activate the shortcut command.

Table 51:

Expansions - via SmartLeague software programme

Option

Part of the system

Template/section

Enable/disable

/

Project

ChoosePeripheral

Expansions - select the expansion

Programming

PROGRAMMING
Arming Scenarios
Shortcuts

Expansions

Expansions

Enable/disable

ChoosePeripheral

PROG. KEYPADS

KEYP. 001

KEYP. 002
KEYP. 003

Keypads
Enable/disable

ChoosePeripheral

PROGRAMMING
Shortcuts
Expansions

Keypads

Keypads

Enable/disable

ChoosePeripheral

«
...
77
78
79
80
81
...
»

Summary of Contents for SmartLiving 10100

















































































































Reviews:

No comments

Related manuals for SmartLiving 10100

Brand: DAB Pages: 8

Brand: Panasonic Pages: 48

Brand: Omega Pages: 2

Brand: D-MAX Pages: 33

MagnaLatch ALERT

Brand: D&D Technologies Pages: 2

Brand: MagicRadar Pages: 98

Brand: Salus Pages: 2

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 7

Brand: Yamaha Pages: 6

Brand: Yamaha Pages: 14

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 8

Brand: Parkside Pages: 113

Brand: Kayoba Pages: 44

Brand: ELRO Pages: 2

SurveyorVFTXX134-60-01

Brand: Vicon Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands