Ness SmartLiving 10100 Installation & Programming Manual Download Page 64

Page: 64 / 112

Options and programming methods

The following table shows the events the control panel recognizes, the number of
events for each type, the trigger and restoral method of each event and the event
category (Pulse).

Table 45:

Event type

Name

Occurs when...

Restores when ...

Number of events

Pulse

events

Zone alarm

A zone generates an alarm

A zone restores

One event for each

zone

Terminal tamper

A terminal detects tamper (short-circuit or

wire cutting)

A terminal restores

One event for each ter-

minal

Partition alarm

A 24h zone which belongs to the partition

generates an alarm, or a zone which

belongs to the partition generates an

alarm during Away mode.

All the zones belonging to the parti-

tion restore (reset).

One event for each

partition

StayPartit.alarm

A zone which belongs to a partition armed

in Stay or Instant mode, generates an

alarm.

All the zones belonging to the parti-

tion restore (reset).

One event for each

partition

Partition tamper

A zone which belongs to the partition

detects tamper (short-circuit or wire

cutting).

All the zones belonging to the parti-

tion restore (reset).

One event for each

partition

Zone bypass

A zone is inhibited

A zone is enabled (switched On)

One event for each

zone

Real-time zone

The electrical status of a zone switches

from standby to alarm

The electrical status of a zone

switches from alarm to standby

One event for each

zone

The event is independent of the zone type and the armed/disarmed status of the

partitions.

Partit.not ready

A zone which belongs to the partition is not

in standby status.

All the zones belonging to the parti-

tion are in standby status.

One event for each

partition

Away arm request

A request is made to arm the interior and

perimeter zones of the partition

A request is made to disarm the par-

tition

One event for each

partition

Yes

Overtime request

A request is made to arm the partition in

Stay mode (perimeter zones only) or in

Instant mode

A request is made to disarm the par-

tition

One event for each

partition

Yes

Partit.AwayArmed

The partition interior and perimeter zones

have been armed effectively

The partition has been disarmed

effectively

One event for each

partition

Partit.StayArmed

armed

The partition has been armed effectively in

Stay or Instant mode

The partition has been disarmed

effectively

One event for each

partition

Partition reset

A request is made to reset the partition

One event for each

partition

Yes

Exit time

The partition exit time is running

The partition exit time expires

One event for each

partition

Entry time

The partition entry time is running

The partition entry time expires

One event for each

partition

Pre-arm time

The partition Pre-arm time is running

The partition Pre-arm time expires

One event for each

partition

Overtime request

A request for overtime relating to the

partition is made

One event for each

partition

Yes

Chime

A chime zone belonging to the partition is

violated

One event for each

partition

Yes

Forced arming

At the time of an arming command, relat-

ing to one or more partitions, there are

open zones on the partition/partitions

involved, or there are other conditions

present which lower system security,

nonetheless, the user arms the system.

One event for each

partition

Yes

Failed to arm

The “OpenZonesArmLock” option is

enabled at the time of a partition arming

command and there is at least one open

zone on the partition/s involved.

when one or more of the conditions

described in “LossTamp.ongoing” is pres-

ent (refer to “FaultForNotReady”,

para-

graph 6-27 Other parameters

One event for each

partition

Yes

Valid code

A user-code PIN entered at a keypad is

recognized as valid

One event for each

code

Yes

Valid key

A key used at a reader is recognized as

valid on the reader

One event for each key

Yes

Valid Code AtKeyp.

A user-code PIN entered at a keypad is

recognized as valid on the keypad

One event for each

keypad

Yes

Summary of Contents for SmartLiving 10100

















































































































Search results

Summary of Contents for SmartLiving 10100

Reviews:

Related manuals for SmartLiving 10100

Brands by name

Popular brands

Ness SmartLiving 10100, Installation & Programming Manual

Search results

Summary of Contents for SmartLiving 10100

Reviews:

Related manuals for SmartLiving 10100

Brands by name

Popular brands