Installation and programming manual
Options and programming methods
51
6-5
Panel options
The following options are provided by the control panel.
Table 42:
Panel options
Option
If enabled
If disabled
Dial tone check
The control panel will engage the telephone line and check for the “dial
tone”, if present, the control panel will start dialing.
The control panel will engage the telephone line,
wait two seconds then will start dialing (whether
the dial tone is present or not).
Pulse dialing
The control panel will dial using pulse tone.
The control panel will dial using touch tone
(DTMF).
DTMF withoutCode
Allows access to the User Menu over-the-phone (during voice calls from
the control panel) in accordance with the parameters and enablements
of the last user code on the control panel (code 30, 50 or 100).
Allows access to the User Menu over-the-phone
during voice calls from the control panel, only
after entry of a valid user-code PIN by the
recipient.
Line down signal
If a “Tel.Line down” event occurs, the control panel will flash the
respective icon
on the keypad displays.
The control panel will detect the “Tel.Line down”
event, but it will not be revealed on the keypad
displays.
Double call
The control panel will override the answerphone function.
Call allVoxNums
If several voice calls - generated by the same event - are waiting in the
outgoing call queue, the control panel will attempt to send voice calls
to all the numbers.
If several voice calls - generated by the same
event - are waiting in the outgoing Call Queue,
the control panel will send voice calls until just
one ends successfully. Any other voice calls
relating to the event in question will be cleared
(deleted) automatically from the queue .
Call all TLVNums
The same as “Call all VOXNums” but valid for Alarm Receiving Centres.
RefreshMnstblOut
Each event that triggers an already-activated monostable output will
refresh (take back to zero) the programmed Monostable time.
Each event that triggers an already-activated
monostable output will not refresh (take back to
zero) the programmed Monostable time.
Num15 ForTeleserv
Telephone number 15 in the phonebook is reserved for Teleservice
(maintenance over-the-phone). If a user makes a request for
Teleservice, the control panel will contact the user's number.
Note
If you wish the control panel to call an installer company number which
uses a Ness modem, you must set “None” in the Telephone Number 15
Type field.
Telephone number 15 in the phonebook can be
dedicated to either voice or teleservice.
Install.callback
The control panel will enable the Teleservice function if:
1.
the installer calls the control panel
2.
the control panel detects the ring, picks up, recognizes the
installer code and hangs up immediately
3.
the control panel calls the Teleservice number and allows
access to the system
ReaderBuzzer OFF
No reader buzzers will emit audible signals during running entry time,
exit time, output time or pre-arm time.
Keypad lockout
If a wrong code is typed-in at a keypad more than 5 times
in succession, the keypad will lock for 10 minutes and show
the icon:
Note
If you reset the control panel or access programming while the keypad-
lockout time is running, it will refresh to zero and start again.
View open zones
The keypad will show the descriptions of any open zones (zones which
are not in standby status) when the partitions disarm. Any
autobypassable open-zones will be shown in white on a black
background.
OpenZonesArmLock
The control panel will not arm the partition if it detects any open zones
(zones which are not in standby status).
If there are zones with the “Auto-bypassable” or “No-Unbypassable”
attribute amongst the open-zones (refer to
paragraph 6-7 Zones
), they
will be shown on the keypad as “Not ready”. If the user goes ahead
with the arming operation, these zones will be bypassed automatically
and the partition will arm.
DTMF sensitivity
The sensitivity of incoming DTMF tones is increased.
BypassAlsoTamper
If a zone is bypassed (disabled), it will also be unable to generate
terminal tamper.
If a zone is bypassed (disabled), it will be able to
generate terminal tamper.
BypassVoiceCheck
The control panel will start the voice message 5 seconds after dialing
the respective contact number.
The control panel will not start the voice
message until it recognizes a voice at the other
end of the line.
