Ness SmartLiving 10100 Installation & Programming Manual Download Page 24 | Manualshive

Page: 24 / 112

background image

24

Installation

3-1-3

Maximum current - normative

references

Compliance with EN50131, CEI 79 or CEB T014 requires full observation of the rules
(relating to the applicable normative and the model of the control panel concerned)
presented in the Table below.

The system must be arranged in such a way that the current draw under normal
circumstances does not exceed the maximum current allowed and the power source for
the battery charge is always available.

3-1-4

Connecting the backup battery

The backup battery [A] connection must be completed during the phase described in

Chapter 4 - First power up

.

The SmartLiving 505, 515 and 1050 control panels house one lead battery @12V 7Ah.

The SmartLiving 10100L house two lead batteries, one @12V 17Ah (Max) and the other
@12V 1.2Ah.

Note

The battery casing must have HB flame rating or higher.

Using the battery wire [B] (included), connect the battery directly to the control panel
motherboard.

ATTENTION!

Ensure that battery polarity is correct:
- black wire = negative
- red wire = positive

The backup battery is the secondary power source which powers the system during
mains failure (230Vac, 50Hz).

Once powered up, the panel will charge and monitor the battery automatically. The
panel tests the efficiency of the battery by simulating load current demand at regular 4
minute intervals. If the control panel detects a voltage inferior to 10.4V (battery
inefficient), it will generate a Low battery event that will not clear until the voltage goes
back to over 11.4V.

This fault will be signalled on the yellow LED on the keypads. To view the fault event,
work through the following steps:

Access User menu

, then View

, Faults Ongoing

.

N

L

230V ~ 50/60 Hz

AC

Input

N L

230V ~ 50/60 Hz

AC Input

SmartLiving10100L

SmartLiving 1050

Table 33:

Maximum current permitted

Norm

SmartLiving intrusion control panels

505

515

1050

10100L

EN50131-3

Maximum current

permitted

1.2A

1.2A

2.6A

3.5A

Current reserved for

the battery charge

1A

1A

2A

2A

CEI 79-2

Maximum current per-

mitted

1.2A

1.2A

2.6A

3.5A

Current reserved for

the battery charge

1A

1A

2A

2A

CEB T014

Maximum current per-

mitted

1.2A

1.2A

2.3A

2.7A

Current reserved for

the battery charge

1A

1A

2A

2A

Faults

Low battery

«
...
22
23
24
25
26
...
»

Summary of Contents for SmartLiving 10100

















































































































Reviews:

No comments

Related manuals for SmartLiving 10100

Brand: D-Link Pages: 2

Brand: D-Link Pages: 40

Brand: D-Link Pages: 8

Brand: D-Link Pages: 6

Brand: D-Link Pages: 4

Brand: D-Link Pages: 41

Brand: Prime Controls Pages: 12

Brand: Vandersteen Audio Pages: 20

Brand: PSB Pages: 2

Brand: EAW Pages: 4

CARPOWER CRB-130SET

Brand: Monacor Pages: 2

Brand: Q-See Pages: 10

Brand: Vivax Metrotech Pages: 78

Brand: RAM Pages: 22

Interlogix RF440I4

Brand: United Technologies Pages: 4

ABIPLAS CUT 200 W/MT

Brand: Abicor Binzel Pages: 100

BeoSound 3000 2671

Brand: Bang & Olufsen Pages: 68

Brand: Velleman Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands