manualshive.com logo in svg

NEC SOPHO IP 5000, Command Reference Manual, Page: 40 / 191

Share
Download
NEC SOPHO IP 5000 Command Reference Manual Download Page 40

 

 

SOPHO 

IP 5000/SOPHO IP6000 

 

Command Reference Guide 

 

40

 

card, power module, and fan module, as well as the offline information of MPU 
and NPU.  

 

Executing the command defined without parameters will display the essential 
information of all the devices in position. Executing the command defined with 
the 

parameter slot-number

 will display only the details on the defined slot, 

including reset times and history records of the reset causes.  

 

Example 

 

Display the essential information of the router.  

 

<NEC-PHILIPS> 

display device 

 

Slot # Type   Online  

Status  

0   RPU     Present  

Normal  

6     PWR    Present    

Normal  

7     FAN     Present  

Normal  

 
 

display schedule reboot   Syntax

 

display schedule reboot  
 
View 

 

Any view  

 

Parameter 

 

None  

 

Description 

 

Using the 

display schedule reboot 

command, you can check the configuration 

of related parameters of the router schedule reboot terminal service. For the 
related command, see r

eboot, schedule reboot at, schedule reboot 

 

delay, undo schedule reboot.  
 
Example 

 

Display the configuration of the schedule reboot terminal service parameters of 
the current router.  

 

<NEC-PHILIPS> 

display schedule reboot  

Reboot system at 16:00:00 2002/11/1 (in 2 hours and 5 minutes).  

 
 

remove slot  

Syntax

  

remove slot slotnum  
undo remove slot slotnum  

 

View  

User view  

 

Parameter 

 

slotnum

: Slot number for the interface card  

 

Description 

 

Using the 

remove slot 

command, you can run pre-processing before removing 

an interface card. You can also cancel a misoperation with the 

undo remove 

slot 

command if you change your mind to remove the card after executing the 

remove slot

 command.  

 
The 

undo remove slot

 command is unnecessary when you remove a card, but 

insert it immediately.  

 

For the related command, see 

reboot, schedule reboot at, schedule reboot 

Summary of Contents for SOPHO IP 5000
































































































































































































Reviews:

No comments