manualshive.com logo in svg

NEC SOPHO IP 5000, Command Reference Manual, Page: 178 / 191

Share
Download
NEC SOPHO IP 5000 Command Reference Manual Download Page 178

 

 

SOPHO 

IP 5000/SOPHO IP6000 

 

Command Reference Guide 

 

178

 

disappear upon the deactivation of  the ADSL port. To transport new services, 
you must re-activate the port.  
 
This command is used to manually activate/deactivate an ADSL line for the  
purpose of testing and troubleshooting.  
 
The commands 

activate/undo activate

 and 

shutdown/undo shutdown

 are  

different because the former can only take effect on ADSL lines.  
 
You should note that ADSL is always online, which is different from DCC.   
 
Therefore, after the device is booted, the ADSL interface will automatically 
enable  the activation task and enter the active state. It will stay active as long 
as the line is  in good condition. The router tests the line performance at a 
regular interval and will automatically deactivate the line and perform a new 
training and re-activation  once it finds out that the line performance has 
deteriorated.  
 

Example  

Deactivate the ADSL interface.  
 
[NEC-PHILIPS-Atm1/0]

undo activate  

 
 

adsl standard  

Syntax  
adsl standard { auto | gdmt | glite | t1413 }  
undo adsl standard  
 
View  

ADSL interface view  
 

Parameter  
auto

: Auto-sensing mode.  

 
gdmt

: Adopts the G.DMT(G992.1) standard.  

 

glite

: Adopts the G.Lite (G992.2) standard. 

 
t1413

: Adopts the T1.413 standard.  

 
Description  

Using the 

adsl standard

 command, you can set the standard applied to an 

ADSL  interface. Using the 

undo adsl standard

 command, you can restore the 

default  standard used by the ADSL interface.  
 
By default, the ADSL standard is set to auto.  
 
You should note that this configuration does not take effect unless you activate  
the interface again. If you want to make it take effect immediately, you can  
execute the 

shutdown/undo shutdown

 command or the 

activate/undo  

activate

 command.  

 

Example  

Set the standard for the interface atm1/0/0 as T1.413.   
[NEC-PHILIPS-Atm1/0/0]

adsl stand t1413  

[NEC-PHILIPS -Atm1/0/0]

shutdown 

  

Interface Atm1/0/0 

has already been shutdown  

[NEC-PHILIPS -Atm1/0/0]

undo shutdown  

[NEC-PHILIPS -Atm1/0/0]  
%Nov 20 21:17:12 2003 5680 PHY/2/PHY:    Atm1/0: change status to up   
%Nov 20 21:17:13 2003 5680 IFNET/5/UPDOWN: 

Summary of Contents for SOPHO IP 5000
































































































































































































Reviews:

No comments