![background image](http://html.mh-extra.com/html/nec/sl1000/sl1000_programming-manual_248471028.webp)
Program
10
t
l
u
a
f
e
D
a
t
a
D
t
u
p
n
I
m
e
t
I
.
o
N
m
e
t
I
13
Loss-Of-Signal Detection Limit
If the transmit/receive voltage is less
than the setting in 10-03-13, the
system considers this as Loss-Of-
Signal and the PRI does not come up.
Note that there are different values
based on the setting in 10-03-12 for
the PRI.
0 = Level 0 (lowest sensitivity)
1 = Level 1
2 = Level 2
3 = Level 3
4 = Level 4
5 = Level 5
6 = Level 6
7 = Level 7 (highest sensitivity)
2
14
Service Protocol for S-point
0 = Keypad facility
1 = Specified Protocol for Aspire system
0
15
Call Busy Mode for S-point
0 = Alerting
1 = Disconnect
0
16
Two B-Channel Transfer for PRI
Service
0 = off
1 = on
0
17
ISDN Ringback Tone
System can provide ringback tone, by
setting 10-03-17 is set to 1:Enable.
0 = Disable
1 = Enable
0
18
Type of Number
ISDN Protocol definition.
Select the number type for the ISDN
circuit.
0 = Unknown
1 = International number
2 = National number
3 = Network Specific number
4 = Subscriber number
5 = Abbreviated number
0
19
Numbering Plan Identification
ISDN Protocol definition.
Select the Numbering Plan used for
the ISDN circuit.
0 = Unknown
1 = ISDN numbering plan
2 = Data numbering plan
3 = Telex numbering plan
4 = National standard numbering plan
5 = Private numbering plan
0
20
Network Exchange Selection
Select the ISDN protocol for the ISDN
circuit.
0 = Standard (same as NI-2)
1 = reserved
2 = reserved
3 = DMS (A211)
4 = 5ESS
5 = DMS (A233)
6 = 4ESS
7 = NI-2
0
21
Number of Ports
0 = Auto
1 = 4 Ports
2 = 8 Ports
3 = 12 Ports
4 = 16 Ports
5 = 20 Ports
6 = 24 Ports
7 = 28 Ports
0
22
QSIG Operation Mode
0 = Disable
1 = Enable
0
23
Straight/Cross Wiring
0 = Auto
1 = Manual (Cross)
2 = Manual (Straight)
0
For DTI (T1) PKG Setup
Physical Port Number
01~30
t
l
u
a
f
e
D
a
t
a
D
t
u
p
n
I
m
e
t
I
.
o
N
m
e
t
I
01
Logical Port Number
The start port number of a T1 line is
displayed, and 24 logic ports are
automatically assigned to a DTI (T1)
line.
0~200
0
02
T1 Signal Format Selection
0 = D4 (12 Multi Frame)
1 = ESF (24 Multi Frame)
0
03
Zero Code Suppression
0 = B8ZS
1 = AMI/ZCS
0
Issue 0.1
SL1000
Program 10 : System Configuration Setup
2-8
Summary of Contents for SL1000
