Home
/
NEC
/
Express5800/T120f
/
Maintenance Manual

NEC Express5800/T120f, Maintenance Manual

Share

Page: 193 / 221

background image

1. POST Error Message

Express5800/R120f-2E, T120f Maintenance Guide

193

Chapter 3 Appendix

Error Message

Cause

Solution

C115

Management controller

not responding

Management controller does
not respond.

Update the BMC firmware.
If the same error is detected repeatedly, contact
your sales representative.

C116

Private I2C bus not

responding.

Private I2C bus does not
respond.

Unplug the power cord, wait for at least 30
seconds, then restart the server. If the same error
is detected repeatedly, contact your sales
representative.

C117

BMC internal exception

BMC internal error was
detected.

C118

BMC A/D timeout error.

BMC A/D timeout error was
detected.

C119

SDR repository corrupt.

BMC error or illegal SDR data
was detected.

C11A

SEL corrupt.

BMC error or illegal system
event log data was detected.

C11B

BMC Mezzanine card is not

found.

BMC Mezzanine card is not
installed.

Contact your sales representative.

C11C

BMC Mezzanine partition is

invalid.

A format error was detected in
BMC Mezzanine card.

C11D

BMC is in Forced Boot Mode.

Detected that BMC is in Forced
Boot Mode.

Unplug the power cord, wait for at least 30
seconds, then restart the server. At that time,
check the jumper switch setting on motherboard.
If the same error is detected repeatedly, contact
your sales representative.

C11E

Communication with BMC was

failed in previous boot

Communication with BMC was
failed in previous boot

Unplug the power cord, wait for 30 seconds, and
restart the server. If the same error is detected
repeatedly, contact your sales representative.

C11F

Backup Data of BMC Mezzanine

card has corrupted.

Inconsistency was found on
BMC mezzanine card.

Contact your sales representative.

C120

BMC Runtime FW corrupted.

An error occurred on BMC
Runtime FW.

Disconnect the power cord, wait for at least 30
seconds, and then restart the server. If the same
error is detected again, contact your sales
representative.

C121

BMC Force Update FW corrupted.

An error occurred on BMC
Force Update FW.

C122

BMC Configuration area

corrupted.

An error occurred on BMC
Configuration area.

C123

BMC eMMC inaccessible.

Failed to access to BMC
eMMC.

C125

BMC eMMC mode error.

BMC eMMC mode error

C126

BMC eMMC partition corrupted.

An error occurred on BMC
eMMC partition.

C127

BMC eMMC format corrupted.

A format error occurred on BMC
eMMC.

C128

BMC is in Update Mode.

BMC is in update mode.

C300

Out-of-band setup

configuration failure

An error was detected while
accessing BMC Mezzanine
card.

Unplug the power cord, wait for at least 30
seconds, then restart the server. If the same error
is detected repeatedly, contact your sales
representative.

«
...
191
192
193
194
195
...
»

Summary of Contents for Express5800/T120f






























































































































































































































Reviews:

No comments

Related manuals for Express5800/T120f

eserver xSeries 440

Brand: IBM Pages: 34

ProtectServer External 2

Brand: SafeNet Pages: 22

Brand: TRENDnet Pages: 135

Brand: BRONKHORST Pages: 19

Brand: Intergraph Pages: 102

Brand: ANTAIRA Pages: 51

ANTMINER S19 Pro

Brand: BITMAIN Pages: 17

Brand: Adaptec Pages: 7

Snap Server 110

Brand: Adaptec Pages: 74

SCB2 - Server Board Motherboard

Brand: Intel Pages: 108

Brand: Uniwide Technologies Pages: 102

Brand: Lantronix Pages: 190

Brand: thomann Pages: 60

QuantaGrid S31A-1U

Brand: QUANTA Pages: 159

Brand: SMC Networks Pages: 19

Brand: Gigabyte Pages: 133

SPARC Enterprise M3000

Brand: Oracle Pages: 552

Brand: tactio Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands