manualshive.com logo in svg

National Instruments AT-MIO-64F-5, User Manual

Share
Download
National Instruments AT-MIO-64F-5 User Manual Download Page 131

Chapter 4

Register Map and Descriptions

© National Instruments Corporation

4-47

AT-MIO-64F-5 User Manual

DMATCA Clear Register

Accessing the DMATCA Clear Register will clear the DMATCA signal in Status Register 1, and
it will acknowledge the interrupt generated from the Channel A terminal counter interrupt.
When the selected DMA channel A reaches its terminal count, the DMATCA signal in the Status
Register is asserted.  If DMATC interrupts are enabled, an interrupt will also be generated.

Address:

Base a 19 (hex)

Type:

Write-only

Word Size:

8-bit

Bit Map:

Not applicable, no bits used.

Strobe Effect:

Clears the DMATCA signal in Status Register 1, and acknowledges an interrupt
from a DMA channel A terminal count.

Summary of Contents for AT-MIO-64F-5











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands