MSI 3750CS-5 User Manual Download Page 79

Page: 79 / 96

CellScale

System • 3750CS-5 User Guide Page 79

MEASUREMENT SYSTEMS INTERNATIONAL

Software V2-21 or greater, 2nd Generation Modem

RESET CALIBRATION

This procedure clears all the calibration parameters and allows a brand new capacity and resolution (count by or

‘d’) to be entered. This procedure should not be used for routine calibration of a previously calibrated Cell Scale

system.

To Reset the Calibration Constants

This procedure will not work if the scale is already in the CAL SETUP menus. Push the EXIT key to get out of “CAL SETUP”.

1) Turn off the 3750CS power. Expose the Calibration

Port by removing the seal screw on the left side of

the 3750CS with a Phillips Screwdriver.

2) Insert a small non-metallic screwdriver and press

and hold on the switch button in the hole.

3) While holding the cal switch on, turn on the 3750CS.

The display reads “RESETALL” for 2 seconds fol-

lowed by “RU SURE”.

4) Push ENTER to reset all registers. The display will

initialize while the registers are cleared.

If you change your mind, pushing EXIT will cancel the Reset All operation.

RESETALL

R U SURE

CALSETUP

RESETCAL

1) Expose the Calibration Seal Port by removing the

seal screw on the left side of the 3750 Meter Casting

with a Phillips Head Screwdriver. The display reads

“CALSETUP”

2) Insert a small non-metallic screwdriver or the wooden

stem of a “Q-Tip” and press and release the switch

button in the hole, followed immediately by the

ZERO key. The display reads “RESETCAL”.

3) The ﬁrst item in the Calibrate Setup Menu appears

(STD CAL). Use the UP or DOWN scroll keys to

locate the desired Calibrate operation.

RESET ALL

This procedure returns all registers of the 3750CS to defaults. DO NOT initiate this function unless you are pre-

pared and qualiﬁed to perform a complete setup of the 3750CS system. This operation differs from RESETCAL

in that all registers are returned to defaults. Communication will be lost until network parameters are reentered.
To Completely Reset the 3750CS

This procedure will not work if the 3750CS is already in the Cal Setup Menus. Push the EXIT key to get out of “CAL SETUP”.

Summary of Contents for 3750CS-5

































































































Search results

Summary of Contents for 3750CS-5

Reviews:

MSI 3750CS-5, User Manual, Page: 79 / 96

Search results

Summary of Contents for 3750CS-5

Reviews: