MSI 3750CS-5 User Manual Download Page 65

Page: 65 / 96

CellScale

System • 3750CS-5 User Guide Page 65

MEASUREMENT SYSTEMS INTERNATIONAL

Software V2-21 or greater, 2nd Generation Modem

PROGRAMMING THE END OF LINE STRING

The End of Line String is used to terminate print strings and is printer dependent. The default string is Line Feed

(LF=ASCII 10). In this example a Carriage Return (CR=ASCII 13) will be added to the EOL String. Refer to the

ASCII table in the Appendix for proper codes. Up to 4 characters can be included. You can even embed a single

@ code to expand the end-of-line string.

EDITING THE PRINT STRING

To change a character

Use the LEFT(<) and RIGHT (>) Scroll keys (Alpha mode must be “n”) to move around in the print string. The

ﬂashing digit indicates the edit able character. Once the desired character is ﬂashing, use the Alpha key to change

to the Alpha mode, then use the letter keys to change it. If you need to change it to a character not in the 3750CS

character set, use the ASCII number entry procedure. Push ENTER twice to store the edited string.

To insert a character

Use the LEFT(<) and RIGHT (>) Scroll keys to move around in the print string. The ﬂashing digit indicates the

edit able character. Insert a new character in front of the ﬂashing digit by pushing the NET/GROSS key. Next

input the desired character. Push ENTER twice to store the edited string.

To delete a character

Position the cursor (blinking character) over the character you wish to delete. Push CLR. The remaining characters

move over 1 space. Push ENTER twice to store the edited string.

Note: Pushing the EXIT key will exit out of the menu and restore the string as it was. The changes must be saved with the double ENTER key push or by pushing
the POWER key.

To disable the Entire Print String

Position the cursor (blinking character) over the ﬁrst character in the Print String. Push INSERT to insert a “

”

(ASCII 255) character at the beginning of the String. Push ENTER twice to store the disabled string. This proce-

dure is more efﬁcient than using the CLEAR key to delete the entire String, especially if the String is very long.

The 3750CS ignores all characters past the ﬁrst “

” it encounters. To enable the string, position the cursor over

the “

” character and push CLEAR. This procedure can also be used to divide a long print string into smaller

parts by inserting a “

” character at discrete locations.

Memory space is always allocated for the Print Strings. There is no benefit to actually deleting characters past the first

GENERAL TEXT/CONTROL CHARACTER ENTRY

Text or control characters are simply entered into the printer data string. All ASCII characters from 0dec to

127dec can be entered with the exception of the “@” symbol which the 3750CS uses for its control characters

(enter “@@” to print a single “@”). If 8 bit data transmission is enabled additional codes 128 to 255 can also

be assigned. These upper numbers are often used for graphics characters on printers. “@” Commands are case

sensitive, only capital letters are used.

Input Data Form

With the exception of characters following the command “@” symbol, all characters are treated as printable text

or control characters. The MSI 3750CS represents characters that can’t be displayed on the LCD with a “

“.

Terminate the string with a dec255 character (ASCII 255). ASCll 255 characters are represented with a “

“. The

“ASCII Entry Mode” is provided to input Control Characters and any other character not included in the standard

3750CS character set. Use the ASCII table (Appendix B) to determine the decimal number equal to any desired

character.

Summary of Contents for 3750CS-5

































































































Search results

Summary of Contents for 3750CS-5

Reviews:

MSI 3750CS-5, User Manual, Page: 65 / 96

Search results

Summary of Contents for 3750CS-5

Reviews: