MSI 3750CS-5 User Manual Download Page 13

Page: 13 / 96

CellScale

System • 3750CS-5 User Guide Page 13

MEASUREMENT SYSTEMS INTERNATIONAL

Software V2-21 or greater, 2nd Generation Modem

Conﬁguring the RF Modem

Assumes F1 is configured as “MODEM”, see “Setup Function Keys”.

1) Push the SETUP key.
2) Push the MODEM key (usually F1). The display

enters the Setup MODEM mode.

3) Push ENTER. The ﬁrst menu item is RF NTWK.

The numeric digits indicate the current network.

4) Change the Network number by pushing the numeric

keys. As soon as you start entering numbers the

screen reads “NEW N/W”. Available network num-

bers range from 0-31.

In this example we’ll use network 12. Use the appropriate numbers for your
CellScale master. It is not necessary to enter a ‘0’ for networks below 10.

Push the 1 key followed by the 2 key.

5) Push ENTER to set your Network choice into

memory. The 3750CS tries to contact the new net-

work while indicating “FINDING”. If the master

unit is on it will connect. If not, the display will ﬂash

brieﬂy “NO NETWK”.

The “NO NETWK” or “NO TARGET” messages can be safely ignored at this
time. It indicates only that the chosen network is not on or in range.

6) Push the UP key to the “C/S ID” menu.
7) Use the numeric keys to change the C/S ID number

to match the SRC address programmed in the

CellScale master. Available C/S ID numbers range

from 0-254.

In this example we’ll use source 75. Use the appropriate numbers for your
CellScale master. It is not necessary to enter leading zeros.

8) Push the ENTER key to set the C/S ID.
9) Push the UP key to the “MY ID” menu. This is the

Node ID of this 3750CS remote.

10) This step is optional. My ID is important only if mul-

tiple slaves are present on the set Network. Use the

Numeric keys to input a unique ID for this 3750CS,

then push ENTER.

11) Push the UP key to the “ENERGY” menu. The

numeric display indicates the current energy level, 2

equals High Power, 1 equals Med Power, 0 indicates

Low power.

12) Press the 0, 1 or 2 key as needed.

MSI recommends using high power (2) in most

installations.

13) This completes the MODEM setup. Push the EXIT

key to return to normal scale operation.

14) If the 3750CS is reporting “NO TARGET” it may

be necessary to send the “Talk to me” message. Do

this by pushing the MODEM key (usually F1).

Enter ID for this 3750CS

NEW ID

ENERGY

Summary of Contents for 3750CS-5

































































































Search results

Summary of Contents for 3750CS-5

Reviews:

MSI 3750CS-5, User Manual, Page: 13 / 96

Search results

Summary of Contents for 3750CS-5

Reviews: