MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 143

Page: 143 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

143

5293079/01 EN

VACUTAP

VM-Ex

6. The magnetic field strength (bushings, busbars etc.) must be < 20 kA/m.

Higher field strengths have a negative effect on the function of the protec-
tive relay.

7. The piping from the protective relay to the oil conservator must be routed

with an inclination of at least 2% (1.2°) to ensure the switching gases can
escape freely.

8. The protective relay is intended for a horizontal operating position in close

proximity to the on-load tap-changer head. A positive inclination of up to
5° from the horizontal is permitted in the direction toward the conservator.
An inclination of up to 5° from the vertical to either side is permitted.

Figure 166: Protective relay installation

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands

MR VACUTAP VM-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands