MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 82

Page: 82 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

5293079/01 EN

VACUTAP

VM-Ex

When actuating the change-over selector, a higher torque is required.

1. Switch the on-load tap-changer into the desired operating position. The di-

verter switch operation can be heard distinctly.

NOTICE!

An incomplete tap-change operation may damage the on-load

tap-changer. After operating the diverter switch, continue to crank the
drive shaft of the upper gear unit for 2.5 revolutions in the same direction
in order to correctly complete the tap-change operation.

3. Perform the transformer ratio test.

4. Repeat the transformer ratio test in all operating positions.

5. Switch the on-load tap-changer into adjustment position (see the accom-

panying connection diagram for the on-load tap-changer).

5.4 Installing on-load tap-changer in transformer (bell-type

tank version)

5.4.1 Inserting on-load tap-changer into supporting structure

5.4.1.1 Fastening tap selector on oil compartment (not for VACUTAP® VM 300)

NOTICE!

Place the selector on a level surface and secure it against tip-

ping. An unstably positioned selector may tip, resulting in severe injuries
and property damage!

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands

MR VACUTAP VM-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands